Abstract:The application of Li-ion conducting garnet electrolytes is challenged by their large interfacial resistance with the metallic lithium anode and the relative small critical current density at which the lithium dendrites short-circuit the battery. Both of these challenges are closely related to the morphology and the structure of the garnet membranes. Here, we prepared four polycrystalline garnet Li6.4La3Zr1.4Ta0.6O12 (LLZTO) pellets with different particle sizes (nano/micro) and grain boundary additive (with/without Al2O3) to investigate the influence of grain size, the composition of the grain boundary, and the mechanical strength of the pellet on the total Li-ion conduction of the pellet, Li/garnet interfacial transfer, and lithium dendrite growth in all-solid-state Li-metal cells. The results showed that the garnet pellets prepared with nanoparticles and LiAlO2-related grain boundary phase had decreased total Li-ion conductivity because of the increased resistance of the grain boundary; however, these pellets showed higher mechanical strength and improved capability to suppress lithium dendrite growth at high current densities. By controlling the grain size and optimizing the grain boundary with Al2O3 sintering additive, the hot-pressing sintered LLZTO solid electrolytes can reach up to 1.01 × 10–3 S cm–1 in Li+ conductivity and 0.29 eV in activation energy. LLZTO with nanosized grain and LiAlO2-modified grain boundary showed the highest critical current density, which is 0.6 mA cm–2 at room temperature and 1.7 mA cm–2 at 60 °C. This study offers a useful guideline for preparing a high-performance LLZTO solid electrolyte.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c18674?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c18674</a>.Feature sizes of LLZTO powders prepared by hand milling and sand milling (Table S1); XRD patterns of hot-pressing sintered samples (Figure S1); element distribution on the polished surface of the sintered samples containing Al2O3 and without Al2O3 by EDX scan (Figure S2); equivalent circuit model for EIS fitting (Figure S3); and LLZTO specimens fractured by three-point bending test, gold sprayed on the surface of the micro-solid electrolyte, an optical photo of the micro-lithium symmetrical battery, and a micro-test fixture designed to test the micro-battery (Figure S4) (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c18674/suppl_file/am0c18674_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Processing Combustion Synthesized Mg0.5Zr2(PO4)3 Nanopowders to Thin Films As Potential Solid Electrolytes

Fe Doped, Dense, High Phase Purity and Nano-Grained Mg0.5zr2(Po4)3 Thin Films

Processing liquid-feed flame spray pyrolysis synthesized Mg 0.5 Ce 0.2 Zr 1.8 (PO 4 ) 3 nanopowders to free standing thin films and pellets as potential electrolytes in all-solid-state Mg batteries

Magnesium Fluoride Interlayers Enabled by Wet‐Chemical Process for High‐Performance Solid‐State Batteries

Developing Preparation Craft Platform for Solid Electrolytes Containing Volatile Components: Experimental Study of Competition between Lithium Loss and Densification in Li7La3Zr2O12

Revealing milling durations and sintering temperatures on conductivity and battery performances of Li2.25Zr0.75Fe0.25Cl6 electrolyte

ZnO-doped BaZr0.85Y0.15O3−δ proton-conducting electrolytes: Characterization and fabrication of thin films

Constructing a Li2O/LiZn Mixed Ionic Electron Conductive Layer by Ultrasonic Spraying to Enhance Li/Garnet Solid Electrolyte Interface Stability for Solid-State Batteries.

Synthesis of Li7La3Zr2O12 Solid Electrolyte by Solid Phase Sintering Method

Facile Construction of Nanofilms from a Dip-Coating Process to Enable High-Performance Solid-State Batteries

Slurry Casted Ultrathin Li3Zr2Si2PO12 Electrolyte Film for Solid‐State Lithium Metal Batteries

Enhanced Performance of Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 Solid Electrolyte by the Regulation of Grain and Grain Boundary Phases

Enhanced Performance of Li6.4La3Zr1.4Ta0.6O12 Solid Electrolyte by the Regulation of Grain and Grain Boundary Phases.

Preparation of dense Ta-LLZO/MgO composite Li-ion solid electrolyte: Sintering, microstructure, performance and the role of MgO

Room-temperature fabrication of garnet-type solid-electrolyte: Optimizing particle size for high ionic conductivity

PVDF-HFP/LiTFSI based composite solid state electrolyte with different micromorphology of Li6.25Ga0.25La3Zr2O12 doping

Fabrication of garnet solid electrolytes via sputtering for solid-state batteries

A Novel Aqueous-based Gelcasting Process to Fabricate Li6.4La3Zr1.4Ta0.6O12 Solid Electrolytes

Spray-Flame Synthesis of NASICON-Type Rhombohedral (α) Li1+xYxZr2-x(PO4)3 [x = 0-0.2] Solid Electrolytes

Preparation of High-Density Garnet Thin Sheet Electrolytes for All-Solid-state Li-Metal Batteries by Tape-Casting Technique

Low-Temperature Manufacture of Cubic-Phase Li7La3Zr2O12 Electrolyte for All-Solid-State Batteries by Bed Powder