Abstract:Ultrashort pulsed laser processing is an effective technology for high-precision cutting, ablation, and drilling of almost all types of material, with low thermal input to the substrate. Polymers which are usually transparent for the laser pulses can be efficiently processed. The material is heated very fast resulting in direct evaporation of the irradiated material volume. On one hand, incubation effects occur due to changed surface roughness, voids, and chemical changes of the material, leading to a variation of energy absorption. On the other hand, if a high repetition rate and high pulse energy are applied to achieve high productivity at polymer cutting, heat accumulation occurs leading to melting and heat affected zones. An estimation of the pulse number dependent material modification and heat input which leads to these effects is not easily accessible for quantitative measurements. Furthermore, numerous process parameters influence the interaction making process analysis and optimization extensive. A versatile tool towards improved knowledge on ultrashort pulsed processes is pump-probe imaging. By using this, effects on a very short timescale such as nonlinear laser absorption, propagation of material waves and plasma generation can be visualized. The recording device in the setup which is applied for the analysis of polymer cutting and drilling in this paper is a high-speed camera with frame rates of up to 50 kHz. This enables recording video sequences contrary to taking a single picture. The authors utilized this to enable the observation of effects of heat accumulation which evolves after a large amount of pulses. Simultaneously, the authors were able to maintain the stated advantages of the pump-probe configuration. Therefore, under variation of several process parameters such as pulse repetition rate, pulse energy, and lateral pulse to pulse separation video sequences were recorded. By a variation of the pump-probe delays of 0 up to 5 ns, material wave propagation can be identified and optimized for evaluation. The points of origin of the observed waves are considered as the regions of highest nonlinear energy deposition; thus, the deposited energy distribution can be estimated. As every single pulse up to a pulse number of 1000 pulses is imaged, the transition from high penetration depth of the first incident pulses to strong surface absorption for an increasing pulse number due to incubation can be shown. Furthermore, strongly absorbing spots in the bulk volume caused by impurities and material modification lead to vapor generation under high pressure. Finally, the confined pressure is assumed to be a main reason for crack formation.

Engraving the Polymer Spherulites with the Pump-Probe Setup Based on Quantum Cascade Laser

Resonant Absorption Induced Fast Melting Studied with Mid-Ir QCLs.

Infrared Microlens Formation on Chalcogenide Polymer Surface Via Femtosecond Laser Pulse Ablation

“Printing” on Polymer Single Crystals Through Microregional Heating

Detection and Characterization of Folded-Chain Clusters in the Structured Melt of Isotactic Polypropyl-Ene.

Directly Probing Molecular Ordering at the Buried Polymer/Metal Interface 2: Using P-Polarized Input Beams

Precise Photochemical Post-Processing of Molecular Crystals.

Pinpoint Two-Photon Writing And Multi-Beam Interferential Patterning Of Three-Dimensional Polymer Photonic Crystals

Terraced and 3D Pyramid‐Shaped Polymer Single Crystal via Low Temperature‐Assisted Microfluidic Technology

High-speed pump-probe imaging of ultrashort pulsed laser cutting of polymers

Effect of Acidic Polymers on the Morphology of Laser-Induced Nucleation of Cesium Chloride

Surface patterns induced by laser irradiation on thin polymer bilayer films

Ultrafast Patterning Of Nanostructures In Polymers Using Laser Assisted Nanoimprint Lithography

Tunable Crystallization Kinetics and Crystal Polymorphism in Semicrystalline Polymers: Insight into the Multilevel Structural Order of Polymer Melts

Mechanism for self-formation of periodic structures on a plastic polymer surface using a nanosecond and femtosecond laser pulses

Revealing Formation Process of Microcapsules During in Situ Polymerization Via Confocal Laser Scanning Fluorescence Microscopy

In Situ Characterization of Thermal‐Induced Evolution of Structure/Optical Properties of Heterogeneous 3D Chiral Soft Photonic Crystal Polymer

Fluorescence microscopy tracking of dyes, nanoparticles and quantum dots during growth of polymer spherulites

Epoxy-Based Azo Polymer for Photofabricating Surface-Relief Quasi-Crystal Structures

Femtosecond Laser Ablated Polymer SERS Fiber Probe with Photoreduced Deposition of Silver Nanoparticles

Studying deformation behavior of a single spherulite with in-situ infrared microspectroscopic imaging