Abstract:Increasing the power conversion efficiency (PCE) of kesterite Cu2ZnSn(S,Se)4 (CZTSSe) solar cells has remained challenging over the past decade, in part due to open-circuit voltage (VOC)-limiting defect states at the absorber/buffer interface. Previously, we found that substituting the conventional CdS buffer layer with In2S3 in CZTSSe devices fabricated from nanoparticle inks produced an increase in the apparent doping density of the CZTSSe film and a higher built-in voltage arising from a more favorable energy-band alignment at the absorber/buffer interface. However, any associated gain in VOC was negated by the introduction of photoactive defects at the interface. This present study incorporates a hybrid Cd/In dual buffer in CZTSSe devices that demonstrate an average relative increase of 11.5% in PCE compared to CZTSSe devices with a standard CdS buffer. Current density-voltage analysis using a double-diode model revealed the presence of (i) a large recombination current in the quasi-neutral region (QNR) of the CZTSSe absorber in the standard CdS-based device, (ii) a large recombination current in the space-charge region (SCR) of the hybrid buffer CZTSSe-In2S3-CdS device, and (iii) reduced recombination currents in both the QNR and SCR of the CZTSSe-CdS-In2S3 device. This accounts for a notable 9.0% average increase in the short-circuit current density (JSC) observed in CZTSSe-CdS-In2S3 in comparison to the CdS-only CZTSSe solar cells. Energy-dispersive X-ray, secondary-ion mass spectroscopy, and grazing-incidence X-ray diffraction compositional analysis of the CZTSSe layer in the three types of kesterite solar cells suggest that there is diffusion of elemental In and Cd into the absorbers with a hybrid buffer. Enhanced Cd diffusion concomitant with a double postdeposition heat treatment of the hybrid buffer layers in the CZTSSe-CdS-In2S3 device increases carrier collection and extraction and boosts JSC. This is evidenced by electron-beam-induced current measurements, where higher current generation and collection near to the p-n junction is observed, accounting for the increase in JSC in this device. It is expected that optimization of the heat treatment of the hybrid buffer layers will lead to further improvements in the device performance.

Efficiency Enhancement of Kesterite Cu2ZnSnS4 Solar Cells Via Solution-Processed Ultrathin Tin Oxide Intermediate Layer at Absorber/Buffer Interface

Sputtering Deposited and Energy Band Matched ZnSnN2 Buffer Layers for Highly Efficient Cd‐Free Cu2ZnSnS4 Solar Cells

A Strategy to Stabilize Kesterite Czts for High-Performance Solar Cells

Improved Cu2ZnSnS4 Solar Cell Performance by Multimetallic Stacked Nanolayers

Low-cost Fabrication of Cu 2 ZnSnS 4 Thin Films for Solar Cell Absorber Layers

Towards a high efficient Cd-free double CZTS layers kesterite solar cell using an optimized interface band alignment

Highly efficient, ultrathin, Cd-free kesterite solar cells in superstrate configuration enabled by band level tuning via Ag incorporation

Enhanced Carrier Collection in Cd/In-Based Dual Buffers in Kesterite Thin-Film Solar Cells from Nanoparticle Inks

A Potential Alternative Deposition Technology for CdS Buffer Layer in Kesterite Solar Cells Via Intermittent Photochemical Deposition

ZnO1−xSx Solid Solution as Potential Buffer Layer Materials for Cu2ZnSnS4‐Based Thin Film Solar Cells: Structural and Interfacial Properties

Over 10% Efficiency Pure Sulfide Kesterite Solar Cells on Transparent Electrode with Cd-Ag Co-Alloying

Improving the efficiency of Cu2ZnSnS4 solar cells by promoting the homogeneous distribution of Sn element

8.36% Efficient CZTS Solar Cells on Transparent Electrode Via Solution Processing

Optimizing efficiency in CHTS-based solar cells through controlling tin content of (Zn, Sn)O buffer layer and integration of SnS as back surface field layer: a numerical approach

Cadmium‐Free Kesterite Thin‐Film Solar Cells with High Efficiency Approaching 12%

Atomic-Scale Interface Modification Improves the Performance of Cu(In1- xGax)Se2/Zn(O,S) Heterojunction Solar Cells

All-Layer Sputtering-Free Cu2Zn1-xCdxSnS4 Solar Cell with Efficiency Exceeding 7.5%

Role of zinc tin oxide passivation layer at back electrode interface in improving efficiency of Cu2ZnSn(S,Se)4 solar cells

Impact on generation and recombination rate in Cu2ZnSnS4 (CZTS) solar cell for Ag2S and In2Se3 buffer layers with CuSbS2 back surface field layer

An ITO‐Free Kesterite Solar Cell

Enhanced solar cell efficiency: copper zinc tin sulfide absorber thickness and defect density analysis