Abstract:AISI 317 L stainless steel replaces 316 L grade in some applications due to its superior mechanical strength and corrosion resistance. Aiming at expanding its applicability to structural applications, ongoing studies are dedicated to overcoming the trade-off between strength and ductility. The stacking fault energy decreases with deformation temperature and favors stacking faulting, (nano)twinning and strain-induced martensite (SIM) formation, resulting in severe microstructural fragmentation. The effect of temperature on deformation behavior of AISI 317 L steel was investigated in samples rolled at room temperature to thickness reductions of 50% and 85% and at 77 K to reductions in thickness of 10% and 50%. The microstructural evolution was followed by scanning electron microscopy, Vickers microhardness, X-ray diffraction, magnetization, electron backscatter diffraction (EBSD) and electron channeling contrast imaging (ECCI). The nucleation sites in the early stages of the transformation sequence γ → ε → α' were identified in the 10% cryorolled sample. The highest volume fraction of α'-martensite reached 45.8% in the cryorolled steel to 50% rolling reduction. Much lower fractions were obtained for samples rolled to 10% reduction at 77 K (2%) and at room temperature to 50% (0.3%) and 85% reductions (1.6%). The texture components after cryorolling were Goss and Brass for austenite; rotated cube, α- and γ-fibers for δ-ferrite and α'-martensite. The ε-martensite presents the typical texture of hcp metals with a c/a ratio above the ideal value and 〈0001〉 − oriented tilted about 21° from the normal direction towards the rolling direction. The results show cryorolling as an effective method for enhancing SIM formation and promoting severe microstructural refinement in AISI 317 L stainless steel.

Influence of Deformation-Induced Martensite on Non-masing Behavior of 304L Stainless Steel

The low-cycle fatigue, deformation and final fracture behaviour of an austenitic stainless steel

Effects of low-cycle fatigue on static mechanical properties, microstructures and fracture behavior of 304 stainless steel

Variation In Mechanical Properties, Microstructures And Fracture Behavior Of 304 Stainless Steel During Low-Cycle Fatigue

Multi-scale Deformation Behavior Investigation of 18cr–8ni Austenitic Steel Subjected to Low-Cycle Fatigue Loading

A study of local mechanical properties of 304L SS welded joints subjected to cyclic straining using depth-sensing instrumented indentation

Use of instrumented indentation testing to study local mechanical properties of 304L SS welded joints subjected to low-cycle fatigue loadings

Deformation Mechanisms of Selective Laser Melted 316l Austenitic Stainless Steel in High Temperature Low Cycle Fatigue

Measurement and Modeling of Deformation-Induced Martensitic Transformation in a Metastable Austenitic Stainless Steel under Cyclic Loadings

Unraveling the Effect of Deformation Temperature on the Mechanical Behavior and Transformation‐Induced Plasticity of the SUS304L Stainless Steel

Strain-induced martensite formation in cryorolled AISI 317 L stainless steel

Kinetics of Deformation-Induced Martensitic Transformation under Cyclic Loading Conditions

Effects of temperature and strain amplitude on low-cycle fatigue behavior of 12Cr13 martensitic stainless steel

Influence of the martensitic transformation on the deformation behaviour of an AISI 316 stainless steel at low temperatures

Role of Strain-Induced Martensitic Phase Transformation in Mechanical Response of 304L Steel at Different Strain-Rates and Temperatures

Modeling of the Kinetics of Strain‐Induced Martensite Transformation and the Transformation‐Induced Plasticity Effect in a Lean‐Alloyed Metastable Austenitic Stainless Steel

Difference between thermal-induced martensite and deformation-induced martensite in 304 austenitic stainless steel

Fatigue and tensile deformation behaviors of laser powder bed fused 304L austenitic stainless steel

Effect of annealing and strain rate on the microstructure and mechanical properties of austenitic stainless steel 316L manufactured by selective laser melting

Deformation induced martensite in an AISI 301LN stainless steel: characterization and influence on pitting corrosion resistance

Characterization of deformation-induced martensite with various AGSs upon Charpy impact loading and correlation with transformation mechanisms