Abstract:In the end milling of superalloy honeycomb cores, the contact form between the cutting tool and honeycomb wall and the force state of the honeycomb wall are variable, there will be difficulties in chip removal. The irregular extension of transverse tearing burrs can deteriorate the machining quality of honeycomb core surfaces, thereby adversely affecting the assembly and service performance of sandwich structures. Based on kinematic analysis, modeling of the removal and deflection process of honeycomb walls was conducted. The feed entrance angle in the case of machining thin walls with high feed speeds was characterized, and the force state of the honeycomb wall and the degree of shear or compression it bears were analyzed. Analytical models of damage scale and single-tooth cutting state were established under different feed entrance angles. The impact of feed entrance angle on the minimum burr length and the minimum constraint failure width was analyzed. The milling experiments of GH4099 superalloy honeycomb wall with ice filling constraint were designed and conducted to clarify the influence of different feed entrance angles on cutting force and transverse tearing burr length. The morphology of burrs and the wear form of the cutting tool were analyzed, and the formation mechanism of transverse tearing burr on the honeycomb sidewalls was revealed. The research results indicate that the feed force F x is 2.1 to 4.7 times greater than the main force F y or the back force F z . When the feed entrance angle is less than 90°, transverse tearing burrs either do not occur, or occur crimped burrs that are gradually removed. Particularly within the range of 0° to 30°, the machining quality is better. The cutting force has a significant shearing effect on the honeycomb wall, making it susceptible to plastic deformation and reaching the fracture strain. The cutting edge can effectively remove material from the honeycomb wall, resulting in normal wear on the minor flank face and tip of the cutting tool. When the feed entrance angle is greater than 90°, it is easy to form large banded burrs, and the burr length is relatively similar to about 1500μm. The cutting force has a significant extrusion effect on the honeycomb wall, resulting in minimal deflection deformation of the honeycomb wall, and making it difficult to fracture. The cutting tool fails to perform effective cutting, leading to increased friction between the cutting tool and honeycomb wall, which continuously induces irregular extension of the burrs. The research findings are of great significance for achieving damage control in metal honeycomb core machining and guiding process and clamping optimization.

Study on the Cutting Force in Machining of Aluminum Honeycomb Core Material

Experimental and Numerical Studies on Defect Characteristics During Milling of Aluminum Honeycomb Core

A New Machining Technique for Cutting NOMEX Honeycomb Core

Numerical Simulation Study on Milling Force for Aerospace Aluminum Alloy

Instantaneous cutting force model considering the material structural characteristics and dynamic variations in the entry and exit angles during end milling of the aluminum honeycomb core

Clamping Technology Optimization of High Speed Machining of NOMEX Honeycomb Core Based on Milling Force Model

Three-dimensional numerical simulation for high speed milling of aerospace aluminum alloy

Simulation of High-Speed Milling Process of Aerospace Aluminum Alloy

Mechanistic modeling considering the bottom edge cutting effect and the material anisotropy during end milling of the aluminum honeycomb core

Fixing System Design of Paper Honeycomb Core for High Speed Milling

Cutting Force Prediction and Experiment Verification of Paper Honeycomb Materials by Ultrasonic Vibration-Assisted Machining

Modeling machining of aluminum honeycomb structure

Modelling of the Temperature Distribution Based on Equivalent Heat Transfer Theory and Anisotropic Characteristics of Honeycomb Core During Milling of Aluminum Honeycomb Core

Influence of feed entrance angle on transverse tearing burr formation in the milling of superalloy honeycomb with ice filling constraint

Machining damage mechanism in end milling of the GH4099 superalloy honeycomb core with ice fixation

Ultrasonic Vibration Assisted Cutting of Nomex Honeycomb Core Materials

Ultrasonic Longitudinal-Torsional Vibration-Assisted Cutting of Nomex® Honeycomb-Core Composites

Investigation on the Effects of Microstructure on Machining Unidirectional Carbon Fiber Reinforced Polymer Composites with a Modified Force Model

Enabling Thin-Edged Part Machining of Nomex Honeycomb Composites via Optimizing Variable Angle of Disc Cutters

Simulated Study of the Machinability of the Nomex Honeycomb Structure

Study on the Design of Cutting Disc in Ultrasonic-assisted Machining of Honeycomb Composites