Abstract:The heat transfer component is a major component of a nuclear power plant, the safety and service life of which are determined based on the long-term creep performance of the heat-transfer pipe material. Several long-term creep tests are usually required to determine the creep life of the heat-transfer pipe materials, which considerably restrict the evaluation efficiency of the material service performance. The objective of this study is to investigate the feasibility of accelerated creep test (ACT) to reduce the time required for evaluating the creep properties of materials. A alumina-forming austenitic (AFA) stainless steel was prepared, and the ACT was performed on a Gleeble thermal simulator. Based on the ACT developed and realized on the Gleeble thermal simulator, damage accumulation was realized by applying elastic-plastic tensile and compressive strains on the ACT specimen to simulate the accelerated changes in the microstructure of the alloy that can be usually observed during a conventional creep test (CT). The average stress with respect to all the cyclic stress relaxation stages in the ACT was considered to be the initial stress of the conventional CT, and a creep fracture test was conducted on the alloy sample. Results revealed that the ACT accelerated the microstructure evolution of the precipitated phases, dislocations, twins, and so on in a short time. Nevertheless, the repeated generation and annihilation of a large number of dislocations in the AFA alloy during the ACT provided the nucleation point and reduced the driving force associated with the nucleation of the precipitated second phase, including the Laves phase. In addition, the cyclic strain applied during the ACT will reduce the strengthening effect of the nanoscale deformation twins in the AFA alloy, resulting in differences in the evaluation effect. Thus, ACT is useful for the efficient evaluation of the creep properties of materials; however, the optimal range of test parameters must be further investigated.

Simulation of the Creep Strain of Carbon-Based Cathode Material in the Aluminum Electrolysis

High Temperature Creep Behaviour of Carbon-Based Cathode Material for Aluminum Electrolysis

Creep Deformation of Carbon-Based Cathode Materials for Low-Temperature Aluminum Electrolysis

High‐Temperature Creep Deformation and Change in Porous Structure of Graphite Cathode in Aluminum Electrolysis Process

Three-dimensional Elastoplastic Phase-Field Simulation of Γ′ Rafting and Creep Deformation

Finite element modeling of creep behavior of porous nickel alloys at the operating conditions of molten carbonate fuel cell

Influence of Current Density on the Microstructure of Carbon-Based Cathode Materials During Aluminum Electrolysis

Study on Multi-Step Creep Aging Behavior of Al-Li-S4 Alloy

Creep Ageing Behaviour Assisted by Electropulsing under Different Stresses for Al−Cu−Li Alloy

Damage in Creep Aging Process of an Al-Zn-Mg-Cu Alloy: Experiments and Modeling

Ab Initio Investigations of Effect of Sodium Intercalation on the Mechanical Performance of Graphitic Cathode During Aluminium Electrolysis

Expansion and creep deformation with microstructure evolution in graphite cathode under constant pressure

Creep Aging Properties Variation and Microstructure Evolution for 2195 Al–Li Alloys with Various Loading Rates

Investigations on the Accelerated Creep Testing of Alumina-Forming Austenitic Stainless Steel

Constitutive modeling and springback simulation for 2524 aluminum alloy in creep age forming

Creep Behavior and a Deformation Mechanism Based Creep Rate Model under High Temperature and Low Stress Condition for Single Crystal Superalloy DD5

Correction to: Creep Deformation of Carbon-Based Cathode Materials for Low-Temperature Aluminum Electrolysis

Investigation of anisotropic creep-ageing behaviour of Al-Cu-Li alloy AA2050

Compressive creep aging behavior and microstructure evolution in extruded Al-Mg-Si alloy under different temperature and stress levels

Creep aging behavior of Al-Cu-Mg-Si alloy with elastic and plastic loads

Cellular automata simulation of cavity growth during creep of Al–Mg alloy