Abstract:High-temperature creep refers to the slow and continuous plastic deformation of materials under the effects of high temperatures and mechanical stress over extended periods, which can lead to the degradation or even failure of the components' functionality. AlxCr0.2NbTiV (x = 0.2, 0.5, or 0.8) refractory high-entropy alloys were fabricated by arc melting. The effects of Al content on the microstructure of AlxCr0.2NbTiV alloys were studied using X-ray diffraction, scanning electron microscopy, and electron backscatter diffraction. The microhardness, compression properties, and nanoindentation creep properties of AlxCr0.2NbTiV alloys were also tested. The results show that the AlxCr0.2NbTiV series exhibits a BCC single-phase structure. As the Al content increases, the lattice constant of the alloys gradually decreases, and the intensity of the (110) crystal plane diffraction peak increases. Adding aluminum enhances the effect of solution strengthening; however, due to grain coarsening, the microhardness and room temperature compressive strength of the alloy are only slightly improved. Additionally, because the effect of solution strengthening is diminished at high temperatures, the compressive strength of the alloy at 1000 °C is significantly reduced. The creep mechanism of the alloys is predominantly governed by dislocation creep. Moreover, increasing the Al content helps to reduce the sensitivity of the alloy to the loading rate during the creep process. At a loading rate of 2.5 mN/s, the Al0.8Cr0.2NbTiV alloy exhibits the lowest creep strain rate sensitivity index (m), which is 0.0758.

High‐Temperature Creep Deformation and Change in Porous Structure of Graphite Cathode in Aluminum Electrolysis Process

High Temperature Creep Behaviour of Carbon-Based Cathode Material for Aluminum Electrolysis

Simulation of the Creep Strain of Carbon-Based Cathode Material in the Aluminum Electrolysis

Expansion and creep deformation with microstructure evolution in graphite cathode under constant pressure

The role of TiB2 particles in the creep and penetrating resistance of graphite-based composite

Ab initio investigations of crystal transition for graphite intercalation compounds during aluminum electrolysiss

Study on the Creep Properties and Microstructures of EW75 Alloy

Finite element modeling of creep behavior of porous nickel alloys at the operating conditions of molten carbonate fuel cell

Influence of Current Density on the Microstructure of Carbon-Based Cathode Materials During Aluminum Electrolysis

In Situ SEM Study of Creep Deformation Behavior of Nickel-Based Single-Crystal Superalloys

Compressive creep aging behavior and microstructure evolution in extruded Al-Mg-Si alloy under different temperature and stress levels

Borated graphite cathodes for low-temperature aluminum electrolysis

Microstructure evolution of Cr 2 AlC MAX phase under a graphite bed between 1100 °C and 1500 °C

Influence of the electrode nano/microstructure on the electrochemical properties of graphite in aluminum batteries

Ab Initio Investigations of Effect of Sodium Intercalation on the Mechanical Performance of Graphitic Cathode During Aluminium Electrolysis

Investigation on creep behaviours of centrifugal casting 27Cr44Ni5W3Al+MA alloy used as ethylene pyrolysis furnace tube at 1050°C

A Study of Bubble Behavior and Anode Effect on the Graphite and Industrial Carbon Anode in a See-Through Furnace During Aluminium Electrolysis

The Influence of Creep Ageing on the Hardening Behavior and Microstructure of 7050 Aluminum Alloy

Influence of temperature on creep behavior, mechanical properties and microstructural evolution of an Al-Cu-Li alloy during creep age forming

Effect of creep-age forming process on precipitation phases of 7B04 aluminum alloy

Effect of Al Content on Microstructure and Properties of AlxCr0.2NbTiV Refractory High-Entropy Alloys