Abstract:Loop heat pipe (LHP) is an efficient phase-change heat transfer device which has been widely applied in cooling high-power electronics on ground and in spacecraft. In previous work, a novel LHP coupled with vapor-driven jet injector (VDJI) has been proved to be feasible and shows excellent performance, namely LHPI. However, due to the lack of pressure data during LHP operation, the coupling mechanisms of VDJI and LHP remain unknown. Especially, the heat-mass transfer between high-speed vapor and subcooled liquid inside VDJI, which has great influence on the LHPI, need to be investigated to guide the design of the LHPI. In this paper, the start-up process, steady-state operation characteristic of LHPI and internal flow field of VDJI were investigated experimentally and numerically. By using the pore-forming sintering and integrated sintering method, the bi-porous wick was prepared and embedded on the base plate surface of evaporator, which brought a significant improvement in its performance. The results indicated that the LHPI could operate under a power of 600 W (50.0 W/cm 2 ) without dry-out. Maintaining the heating wall temperature within 85 °C, the minimum thermal resistance of the LHPI with bi-porous and integrated sintered wick was below 0.18, and the maximum heating power can reach up to 404 W, which are 60% lower and 52.5% higher than mono-porous wick, respectively. In addition, four operation modes of VDJI were classified as low-efficiency mode, normal-injection mode, restricted expansion mode and superheated mode. The operation modes of VDJI had great influence on the performance of LHPI. In normal-injection mode, the entrainment ratio of VDJI exceeded 100, which resulted in the lowest thermal resistance of LHPI. For long-term operation of LHPI, the VDJI is suggested keep operating in normal-injection mode. Moreover, by using 3D numerical simulation method, the internal flow structure of the VDJI was obtained to gives an insight into mechanisms of these four operation modes. The numerical results showed the profile of compression waves and confirmed the existence of condensation shock wave in VDJI.

Visual Investigation on Startup Characteristics of a Novel Loop Heat Pipe

Visualized Investigation of Gas–liquid Stratified Flow Boiling of Water in a Natural Circulation Thermosyphon Loop with Horizontal Arranged Evaporator

Two-phase Flow Oscillation and Distribution in Parallel Channels During R1233zd(E) Subcooled Flow Boiling: A Numerical Study

Visualized Investigation of the Onset of Flow Boiling Dynamic Instabilities in a Horizontal Arranged Tube under a High-Temperature Thermal Storage Boundary Condition

Study on the startup and heat transfer performance of loop heat pipe under sloshing conditions

Experimental Investigation on a Loop Thermosyphon with Three Evaporators: Unique Startup and Oscillation Phenomena

Experimental Study of Flow Boiling Instabilities in Horizontal Tubes under Gas–liquid Stratification Condition: Effects of Heat Flux and Inlet Subcooling Degree

Mesoscopic numerical study of the startup characteristics of grooved heat pipe under high heat flux

Startup influencing factor investigation and quantitative interaction analysis on a loop thermosyphon with multiple evaporators

Experimental investigation on the start-up performance of a novel flat loop heat pipe with dual evaporators

Numerical investigation on the startup performance of high-temperature heat pipes for heat pipe cooled reactor application

Experimental Study on the Dynamic Heat Transfer Characteristics of a Mechanically Pumped Two-phase Cooling Loop

Experimental Investigation on Flow Behavior During Start-up of a Heating Reactor

Experimental Study on an Thermosyphon Loop with Bubble Pump Effect

Visualization study of a flat confined loop heat pipe for electronic devices cooling

Regulation of Gas-Liquid Stratified Flow Boiling Dynamic Instabilities in Horizontal Tube: Effects of Heat Load Distribution and Wall Thermal Capacity

Performance of a novel loop heat pipe coupled with micro vapor-driven jet injector – An experimental and numerical study

Numerical investigation on transient and steady phase change heat transfer in the evaporator of a loop heat pipe

Experimental investigation on the thermal performance of a novel loop heat pipe (LHP) with micro-channel structure

Experimental study on startup performance of high temperature potassium heat pipe at different inclination angles and input powers for nuclear reactor application

Experimental Study on Startup and Heat Transfer Performance of High Temperature Sodium Heat Pipe