Abstract:<p>A high-temperature in-situ tensile stage setup developed by the authors was combined with electron backscatter diffraction (EBSD) to study the microstructural evolution behavior of Ti–6Al–4V alloy produced by laser direct melting deposition (LDMD) at 400 °C. This technique provided direct observation of the microstructure evolution and deformation behavior of materials under dynamic tensile loading at operating temperature. The evolution of grain morphology, misorientation angles of grain boundaries, and Schmid factor (SF) were systematically investigated. The results indicated that the grains no longer sustained the initial lamellar morphology and underwent a severe microstructural evolution during plastic deformation. Various grain morphologies were observed at different tensile strain levels. The statistical analysis revealed the reduction of high-angle grain boundaries' (HAGBs) fraction among α/α grains, with the opposite trend for low-angle grain boundaries (LAGBs). The increased Schmid factor values (SF > 0.4) were observed for prismatic (1–100) <11–20> and pyramidal (1–101) <11–20> slip systems, while those of the basal (0001) <11–20> slip system exhibited a sharp drop to SF > 0.4 at higher strain levels. Moreover, it was observed that high-SF grains changed their orientations, while low-SF ones split into smaller grains under tensile load. The kernel average misorientation (KAM) maps showed that deformation promoted dislocation motion, generating many LAGBs. The increasing number of LAGBs and slip openings reduced the boundary resistance and provided an easy path to detour the main crack propagation in response to the applied stress, while the LDMD Ti–6Al–4V specimen showed ductile fracture behavior.</p>

Statistical TEM analysis of boundary misorientations in aluminium deformed to large and extra large strains by ECAE

Microstructural and texture evolution investigation of laser melting deposited TA15 alloy at 500?C using in-situ EBSD tensile test

Characterization of Boundary Misorientations in A Superplastic Al-Alloy Hot-Deformed by Ecae

3D microstructural and strain evolution during the early stages of tensile deformation

Structural Coarsening During Annealing of an Aluminum Plate Heavily Deformed Using ECAE

In-situ Study of the Effect of Strain Path Change on Dislocation Boundary Evolution in Commercial Purity Aluminum

Critical Comparison of Dislocation Boundary Alignment Studied by TEM and EBSD: Technical Issues and Theoretical Consequences

Strain Distribution and Lattice Rotations During In-Situ Tension of Aluminum with a Transmodal Grain Structure

Characterization and Influence of Deformation Microstructure Heterogeneity on Recrystallization

EBSD-Based Techniques for Characterization of Microstructural Restoration Processes During Annealing of Metals Deformed to Large Plastic Strains

Effect of second-phase precipitates on deformation microstructure in AA2024 (Al–Cu–Mg): dislocation substructures and stored energy

Investigating the microstructural evolution during deformation of laser additive manufactured Ti–6Al–4V at 400 °C using in-situ EBSD

In-situ Study of Microstructural Evolution and Local Strain Distribution During Tensile Loading of Near-Micrometre Grain Size Aluminium

Application of aberration‐corrected scanning transmission electron microscopy in conjunction with valence electron energy loss spectroscopy for the nanoscale mapping of the elastic properties of Al–Li–Cu alloys

Investigation of anisotropy evolution of an aluminium‐lithium alloy with increasing pre-deformation in creep age forming

Elastic strain mapping of plastically deformed materials by TEM

3D Ebsd Characterization of Deformation Structures in Commercial Purity Aluminum

Investigation of Medium to High Strain Deformation Microstructures Using an Automated Electron Backscattering Pattern (EBSP) System

Comparative Microstructural Characterization of a Friction-Stir-welded Aluminum Alloy Using TEM and SEM-based Techniques

Dislocation Structures In Deformed Metals