Abstract:A two-dimensional model for the simulation of solidification microstructure in multi-component alloy systems has been developed. The model is based on a cellular automaton (CA) technique for the calculation of the evolution of solid/liquid (S/L) interface. The dynamics of the interface is controlled by temperature, solute diffusion and Gibbs-Thomson effects. The diffusion equation for the temperature with release of latent heat on the S/L interface is valid in the entire domain, and the solute diffusion equation is also used in the entire domain through potential functions. Two methods are proposed to calculate the increment of the solid fraction. The first method is based on the level rule method similar to the one proposed by Jacot et al., but without the assumption of uniform temperature on the scale of the calculation domain. The second one is based on the calculation of the S/L interface velocity, which generalizes the results of Nastac and Beltran-Sanchez et al. for two-component alloy systems. If the concentration of one of the solutes tends to zero, both proposed methods reduce to the methods in Jacot et al. and Beltran-Sanchez et al. for two component alloy systems. Mesh independency is achieved by both methods and the dendritic morphologies obtained are the same if the mesh is fine enough. However, the morphologies of equiaxed dendrites calculated by using the interface velocity tends to the stable form more easily than those calculated using the level rule method as the mesh size is refined. For two-component alloy systems, the predictions of LGK theory for the steady-state tip velocity are compared with simulated values as a function of melt undercooling, which shows good agreement at very large range of undercooling. The simulated primary arm spacing in directional solidification is compared with experimental results for Fe-Si-Mg alloys and good agreement is also observed. It is noted that both methods for computing the solid fraction can be used for any multi-component alloy systems provided that the thermodynamic data are given

Experimental Study and Cellular Automaton Simulation on Solidification Microstructure of Mg–Gd–Y–Zr Alloy

Modeling of Grain Refinement and Nucleation Behavior of Mg-4Y-0.5Zr (wt.%) Alloy Via Cellular Automaton Model

Effect of Cooling Rate on the Solidified Microstructure of Mg-Gd-Y-Zr Alloy

Simulation of Magnesium Alloy AZ91D Microstructure Using Modified Cellular Automaton Method

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

Phase-Field Simulation on the Influence of Cooling Rate on the Solidification Microstructure of Mg-Gd-Y Ternary Magnesium Alloy

An Efficient Analytical Model for Predicting the Microstructure Characteristic Parameters of the As-Cast and Solid-Solution Treated Mg-Gd-Y-Zr Cast Alloys

Influence of Solute Content and Cooling Rate on the Preparation of Semi-Solid Slurries for Novel Creep-Resistant Mg-Gd-Ca-Zr Alloys

The Effect of Cooling Rate on the Microstructure and Mechanical Properties of Mg–Zn–Gd-based Alloys

Simulation Study of Evolution Mechanisms of Microstructures During Rapid Solidification of Liquid Mg-7 Zn-3 Alloy

Numerical Simulation of Solidified Microstructure of Ternary Al-Si-Mg Alloy Using an Improved Cellular Automaton Method

Study of the Dynamic Recrystallization Behavior of Mg-Gd-Y-Zn-Zr Alloy Based on Experiments and Cellular Automaton Simulation

Simulation of Mg-Gd Alloy During Solidification Process

Microstructure Simulation of Die Casting AZ91D Alloy

Numerical Modeling of Grain Refinement During Solidification of Mg-4Y-3Nd (wt.%) Alloy Via Mesh-Anisotropy Reduction Algorithm

Cellular Automaton Modeling of Semi-Solid Microstructure Formation

Microstructure Simulation of Die Casting Magnesium Alloy

Influence of cooling rate on microstructure and solution behavior of Mg-Gd-Y-Zr alloy

A Cellular Automaton Technique for the Modeling of Solidification Microstructure in Multi-Component Alloys

Numerical Investigation of Grain Refinement of Magnesium Alloys: Effects of Cooling Rate

Microstructures and Mechanical Properties of As-Cast Mg-Sm-Zn-Zr Alloys with Varying Gd Contents