Abstract:Modulation of the microstructure and configurational entropy tuning are the core stratagem for improving thermoelectric performance. However, the correlation of evolution among the preparation methods, chemical composition, structural defects, configurational entropy, and thermoelectric properties is still unclear. Herein, two series of AgSbTe2-based compounds were synthesized by an equilibrium melting-slow-cooling method and a nonequilibrium melting-quenching-spark plasma sintering (SPS) method, respectively. The equilibrium method results in coarse grains with a size of >300 μm in the samples and a lower defect concentration, leading to higher carrier mobility of 10.66 cm2 V-1 s-1 for (Ag2Te)0.41(Sb2Te3)0.59 compared to the sample synthesized by nonequilibrium preparation of 1.83 cm2 V-1 s-1. Moreover, tuning the chemical composition of nonstoichiometric AgSbTe2 effectively improves the configurational entropy and creates a large number of cation vacancies, which evolve into dense dislocations in the samples. Owing to all of these in conjunction with the strong inharmonic vibration of lattice, an ultralow thermal conductivity of 0.51 W m-1 K-1 at room temperature is achieved for the (Ag2Te)0.42(Sb2Te3)0.58 sample synthesized by the equilibrium preparation method. Due to the enhanced carrier mobility, optimized carrier concentration, and low thermal conductivity, the (Ag2Te)0.42(Sb2Te3)0.58 sample synthesized by the equilibrium preparation method possesses the highest ZT of 1.04 at 500 K, more than 60% higher than 0.64 at 500 K of the same composition synthesized by nonequilibrium preparation.

Comparison of microstructure and thermoelectric properties of SnTe Bi2Te3 compounds prepared by two different methods

Solvothermal preparation and thermoelectric properties of quasi-binary Sn(Pb) Te-Bi 2 Te 3 compounds

Microstructure and thermoelectric properties of porous Bi 2 Te 2.85 Se 0.15 bulk materials fabricated by semisolid powder processing

Thermoelectric properties and microstructure of SnTe-Bi2Te3 alloys

Nanostructuring and improved performance of ternary Bi–Sb–Te thermoelectric materials

Improved Thermoelectric Properties of Bi2Te3−xSexalloys by Melt Spinning and Resistance Pressing Sintering

Structures and Electric Properties of Bi2Te3 Based Alloys Prepared by Solvothermal Synthesis

Effect of solvent on the microstructures of nanostructured Bi 2Te3 prepared by solvothermal synthesis

Transport Properties of SnTe–Bi2Te3 Alloys

Enhancing Thermoelectric Performance of AgSbTe 2 -Based Compounds via Microstructure Modulation Combining with Entropy Engineering

Synergistic Effect of Bismuth and Indium Codoping for High Thermoelectric Performance of Melt Spinning SnTe Alloys

Optimization Method and Performance Study of Bi2Te3 Nanosheets Preparation Based on Solvothermal Method

Systhesizing Snte Nanocrystals Leading to Thermoelectric Performance Enhancement Via an Ultra-Fast Microwave Hydrothermal Method

Enhancing Thermoelectric Performance of SnTe Via Nanostructuring Particle Size

Effect of Preparation Methods on Thermoelectric Properties of N-type Bi_2Te_(2.4)Se_(0.6) Bulk Alloys

Comparative Study of Thermoelectric Properties of Sb2Si2Te6 and Bi2Si2Te6

Enhanced figure of merit in nanostructured (Bi, Sb) 2 Te 3 with optimized composition, prepared by a straightforward arc-melting procedure

Bulk Nanostructured Thermoelectric Materials: Preparation, Structure and Properties

Effect of PbTe on Thermoelectric Properties of Co 0.88 Ni 0.12 Sb 2.91 Sn 0.09

Microstructure and thermoelectric performance evaluation of p-type (Bi, Sb)2Te3 materials synthesized using mechanical alloying and spark plasma sintering process

Syntheses and Thermoelectric Properties of Bi2te3/Sb2te3 Bulk Nanocomposites with Laminated Nanostructure