Abstract:The hot deformation behaviors of Fe–28Mn–10Al–1.5C–0.6V steel at T = 950–1150 °C and = 0.01–10 s −1 were studied using the Gleeble-3500 thermo-mechanical simulator. The constitutive model of Fe–28Mn–10Al–1.5C–0.6V steel was established by an artificial neural network (ANN) based on the experimental flow stress data. The critical conditions of dynamic recrystallization (DRX) of the steel under experimental conditions were studied by using both the Najafizadeh–Jonas work hardening rate model and the Cingara–McQueen rheological stress model. The true stress–true strain curve of the steel was analyzed, the work hardening rate was calculated, and the critical strain model was established. At the same time, the relevant material parameters were calculated by linear regression, and the DRX kinetics model of JMAK was also established. This model then was combined with the finite element software DEFORM-3D to simulate the DRX behavior of the steel during hot deformation. These results indicated that the rheological stress of Fe–28Mn–10Al–1.5C–0.6V steel at low shows higher temperature sensitivity and that high T and low are conducive to the occurrence of DRX. The average relative error of the ANN constitutive model is 2.40%, which has high prediction accuracy. The dynamic recrystallization conditions determined by the above models are reliable and conform to the experimental rules. By verifying the microstructure of the steel after thermal compression, the prediction error of the finite element model to the DRX volume fraction is mostly within 10%. Thus, the model has a good predictive ability and provides an effective tool for predicting plastic deformation and microstructure in industrial production.

The Study on Kinetics of Metadynamic Recrystallisation of a Nb-V Microalloyed Non-Quenched and Tempered Steel

Study on Dynamic Recrystallization of Nb-Microalloyed Steels

Research on hot deformation, dynamic recrystallization and numerical simulation of Fe–28Mn–10Al–1.5C–0.6V steel

Dynamic Recrystallization Behaviour of Nb-Ti Microalloyed Steels

An improved cellular automaton model of dynamic recrystallization and the constitutive model coupled with dynamic recrystallization kinetics for microalloyed high strength steels

Kinetics and microstructure evolution of dynamic recrystallization of medium-Mn steel during hot working

Constitutive Modeling and Dynamic Recrystallization Mechanisms of an Ultralow-carbon Microalloyed Steel During Hot Compression Tests

Modeling of Dynamic Recrystallization and Flow Stress of Nb‐Bearing Steels

Static Recrystallization Behavior of Low-Carbon Nb-V-Microalloyed Forging Steel

Thermal deformation behavior and microstructure evolution of Fe−8.5Mn−1.5Al light−weight medium manganese steel

Study on dynamic recrystallization of ultra-high strength 22MnB5 steel during hot rolling

Study on dynamic recrystallization behavior of 1MnCrMoNi steel during hot compression deformation

Dynamic Recrystallization Behavior of Fe–20Cr–30Ni–0.6Nb–2Al–Mo Alloy

Effect of Nb, Ti microalloying on hot deformation behavior of high strength steel

Microstructure simulation and experiment investigation of dynamic recrystallization for ultra high strength steel during hot forging

Study of static recrystallization behavior of austenite in a Ti–V microalloyed steel

High Temperature Deformation Behavior and Microstructure Evolution of Low-Density Steel Fe30Mn11Al1C Micro-Alloyed with Nb and V

Modeling of Dynamic Recrystallization Kinetics of a High Strength Low Alloy Steel During Hot Rolling

Modelling of Microstructure Evolution During Hot Rolling of a High-Nb HSLA Steel

Effect of Niobium and Titanium on Dynamic Recrystallization Behavior of Low Carbon Steels

Dynamic Recrystallization Behavior and Constitutive Modeling of As-Cast 30cr2ni4mov Steel Based on Flow Curves