Abstract:A compact x-band hybrid dielectric-iris-loaded travelling-wave linac with constant impendence structure has been designed. By adjusting the values of φ β and the numbers of cells, the beam energy of 33 MeV, the capture efficiency about 50% and the energy spread about 3% ± with the beam current being 70 mA and the electron gun voltage being 50KeV are obtained through longitudinal dynamics calculation. The length of accelerator tube is 1.48m. The maximum accelerating gradient is less than 45MV/m. By using electromagnetic code such as MAFIA, the attenuation per unit length of structureα , the shunt impedance s Z , the quality factor Q, the group velocity g β and the phase velocity φ β are got by optimizing the dimensions of the cavities. INTRODUCTION X-band high-gradient accelerator has been progressed greatly in recent years, motivated by the need for the future linear colliders in high energy physics research and for the industrial and medical application. By developing X-band high gradient accelerating structure, one can use a shorter length for a given power to achieve certain electron beam energy. There are obvious advantages for using X-band range than S-band one. First, the shunt impedance per unit length of X-band is higher than that of S-band. Second, the maximum permissible electric field strength is also higher. One disadvantage of conventional iris-loaded accelerating structures is the high ratio of the peak surface electric field to the peak axial electric field. Typically this ratio of Es/Ea is more than 2. The high surface electric field relative to the accelerating gradient may prove to be a limitation for realizing technologies for very high gradient accelerators. A hybrid dielectric and iris loaded periodic structure can reduce Es/Ea to near unity, while maintaining high acceleration efficiency as measured by r/Q compare favourably with conventional metallic structures[1] and the r/Q values of dipole modes for the new accelerating structure are much lower than those for the iris-load accelerating structure[2]. The device is shown in figure 1. This paper presents a design of an x-band (11.424GHz) hybrid dielectric and iris loaded travelling wave electron linear accelerator with beam energy of 33 MeV and beam current of 70 mA. The longitudinal dynamics for this accelerator and the RF parameters are calculated. Figure 1: Sketch of regular accelerator cavities. In the figure, region I is vacuum; region II is ceramic with dielectric constant r ε ; region III is copper. a is the iris radius, b is the outer radius, and h is the beam hole radius. t is the thickness of the iris, and d is the length of one cell. DESIGN OF THE NEW ACCELERATING STRUCTURE

Development of x-band photonic band gap accelerating structure

X-band two-dimensional metallic photonic crystal accelerating structure

Simulation And Fabrication Research On X-Band Photonic Band Gap Accelerating Structure

Simulations for the advanced photonic band gap accelerating structure

Investigations Of Photonic Band Gap Microwave-Driven Accelerating Cavity

Research of metal-dielectric photonic crystal accelerating structures

Calculation of Wakefields in a 17 GHz Beam-Driven Photonic Band-Gap Accelerator Structure

New Construction of Hybrid and Aperiodic Ordered PBG Cavity

Preliminary studies on the photonic crystal accelerating structure

Design, Fabrication and Cold-Test of an X-band Accelerating Structure for Linearizer

Investigations on the multi-sector hard X-Band Structures

Coupler Design and Test for X-band Hybrid Loaded Circular Waveguide Accelerator

Hybrid photonic-bandgap accelerating cavities

Design and Test of an X-band Constant Gradient Structure

Coupler Design For X-Band Hybrid Dielectric-Iris Loaded Accelerator

Design and Fabrication of a Planar Coupling Structure for Photonic Band Gap Devices

Novel Photonic Bandgap Structure And Its Application In Amplifier

Development of an x-band hybrid dielectric-iris-loaded accelerator *

A Compact X-band Backward Traveling-Wave Accelerating Structure

PIC Simulation and Preliminary Experiment on a G-band Sheet Beam Traveling-Wave Tube

Fabrication and high power rf test of a c-band 6MeV standing-wave linear acceleratingstructure