Abstract:Vibration-based Structural Health Monitoring (SHM) techniques are among the most common approaches for structural damage identification. The presence of damage in structures may be identified by monitoring the changes in dynamic behavior subject to external loading, and is typically performed by using experimental modal analysis (EMA) or operational modal analysis (OMA). These tools for SHM normally require a limited number of physically attached transducers (e.g. accelerometers) in order to record the response of the structure for further analysis. Signal conditioners, wires, wireless receivers and a data acquisition system (DAQ) are also typical components of traditional sensing systems used in vibration-based SHM. However, instrumentation of lightweight structures with contact sensors such as accelerometers may induce mass-loading effects, and for large-scale structures, the instrumentation is labor intensive and time consuming. Achieving high spatial measurement resolution for a large-scale structure is not always feasible while working with traditional contact sensors, and there is also the potential for a lack of reliability associated with fixed contact sensors in outliving the life-span of the host structure. Among the state-of-the-art non-contact measurements, digital video cameras are able to rapidly collect high-density spatial information from structures remotely. In this paper, the subtle motions from recorded video (i.e. a sequence of images) are extracted by means of Phase-based Motion Estimation (PME) and the extracted information is used to conduct damage identification on a 2.3-m long Skystream® wind turbine blade (WTB). The PME and phased-based motion magnification approach estimates the structural motion from the captured sequence of images for both a baseline and damaged test cases on a wind turbine blade. Operational deflection shapes of the test articles are also quantified and compared for the baseline and damaged states. In addition, having proper lighting while working with high-speed cameras can be an issue, therefore image enhancement and contrast manipulation has also been performed to enhance the raw images. Ultimately, the extracted resonant frequencies and operational deflection shapes are used to detect the presence of damage, demonstrating the feasibility of implementing non-contact video measurements to perform realistic structural damage detection.

Modal Parameter Identification and Damage Localization of Composite Helicopter Rotor Blades Based on AR/PR Identification

Analysis of Vibration Monitoring Data of an Onshore Wind Turbine under Different Operational Conditions

Damage Mode Identification of Composite Wind Turbine Blade under Accelerated Fatigue Loads Using Acoustic Emission and Machine Learning

Damage Mode Identification and Singular Signal Detection of Composite Wind Turbine Blade Using Acoustic Emission

Application of Artificial Neural Networks to a Model of a Helicopter Rotor Blade for Damage Identification in Realistic Load Conditions

Experimental Study of Structural Damage Identification Based on Modal Parameters and Decay Ratio of Acceleration Signals

Damage identification of wind turbine blades using the microphone array under different parametric and measuring conditions: A prototype study with laboratory-scale models

Research on Online Monitoring of Wind Turbine Blade Damage Based on Working Mode Analysis

Statistical Structural Integrity Control of Composite Structures Based on an Automatic Operational Modal Analysis — a Review

Vibration-based damage detection in wind turbine blades using Phase-based Motion Estimation and motion magnification

Structural Health Monitoring of Carbon Fiber Reinforced Polymer Composite Laminates for Offshore Wind Turbine Blades Based on Dual Maximum Correlation Coefficient Method

Aeroelastic analysis and structural parametric design of composite rotor blade

A method to distinguish harmonic frequencies and remove the harmonic effect in operational modal analysis of rotating structures

Modal Identification of Aircraft Time-varying Structure Based on Fiber Grating Measurement

Dynamic modeling and parametric instability analysis of internally damped rotating composite shafts in inertial and rotating frames

Exploration on flutter mechanism of a damaged transonic rotor blade using high-fidelity fluid–solid coupling method

Damage Identification of Wind Turbine Blades Using an Adaptive Method for Compressive Beamforming Based on the Generalized Minimax-Concave Penalty Function

Monitoring Based Fatigue Damage Prognosis of Wind Turbine Composite Blades under Uncertain Wind Loads

Spatial-Vibration-Modulation-Assisted Blade Damage Localization for Industrial Quadrotor UAVs

Damage diagnosis of plates and shells through modal parameters reconstruction using inverse finite-element method

An Adaptive Chirp Mode Decomposition-Based Method for Modal Identification of Time-Varying Structures