Abstract:Vibration-based Structural Health Monitoring (SHM) techniques are among the most common approaches for structural damage identification. The presence of damage in structures may be identified by monitoring the changes in dynamic behavior subject to external loading, and is typically performed by using experimental modal analysis (EMA) or operational modal analysis (OMA). These tools for SHM normally require a limited number of physically attached transducers (e.g. accelerometers) in order to record the response of the structure for further analysis. Signal conditioners, wires, wireless receivers and a data acquisition system (DAQ) are also typical components of traditional sensing systems used in vibration-based SHM. However, instrumentation of lightweight structures with contact sensors such as accelerometers may induce mass-loading effects, and for large-scale structures, the instrumentation is labor intensive and time consuming. Achieving high spatial measurement resolution for a large-scale structure is not always feasible while working with traditional contact sensors, and there is also the potential for a lack of reliability associated with fixed contact sensors in outliving the life-span of the host structure. Among the state-of-the-art non-contact measurements, digital video cameras are able to rapidly collect high-density spatial information from structures remotely. In this paper, the subtle motions from recorded video (i.e. a sequence of images) are extracted by means of Phase-based Motion Estimation (PME) and the extracted information is used to conduct damage identification on a 2.3-m long Skystream® wind turbine blade (WTB). The PME and phased-based motion magnification approach estimates the structural motion from the captured sequence of images for both a baseline and damaged test cases on a wind turbine blade. Operational deflection shapes of the test articles are also quantified and compared for the baseline and damaged states. In addition, having proper lighting while working with high-speed cameras can be an issue, therefore image enhancement and contrast manipulation has also been performed to enhance the raw images. Ultimately, the extracted resonant frequencies and operational deflection shapes are used to detect the presence of damage, demonstrating the feasibility of implementing non-contact video measurements to perform realistic structural damage detection.

Structural Health Monitoring of Carbon Fiber Reinforced Polymer Composite Laminates for Offshore Wind Turbine Blades Based on Dual Maximum Correlation Coefficient Method

Damage Mode Identification and Singular Signal Detection of Composite Wind Turbine Blade Using Acoustic Emission

Damage Mode Identification of Composite Wind Turbine Blade under Accelerated Fatigue Loads Using Acoustic Emission and Machine Learning

3D Multiscale Dynamic Analysis of Offshore Wind Turbine Blade under Fully Coupled Loads

Structural Health Monitoring of Composite Wind Turbine Blades: Challenges, Issues and Potential Solutions

Condition-based structural health monitoring of offshore wind jacket structures: Opportunities, challenges, and perspectives

Statistical Structural Integrity Control of Composite Structures Based on an Automatic Operational Modal Analysis — a Review

An Overview on Structural Health Monitoring and Fault Diagnosis of Offshore Wind Turbine Support Structures

Vibration-based damage detection in wind turbine blades using Phase-based Motion Estimation and motion magnification

Progress and Trends in Damage Detection Methods, Maintenance, and Data-driven Monitoring of Wind Turbine Blades – A Review

An Integrated Acousto/Ultrasonic Structural Health Monitoring System for Composite Pressure Vessels

Monitoring fatigue delamination growth in a wind turbine blade using passive thermography and acoustic emission

Nondestructive evaluation of carbon-fiber composites using digital image correlation, acoustic emission, and optical based modal analysis

Finer SHM-Coverage of Inter-Plies and Bondings in Smart Composite by Dual Sinusoidal Placed Distributed Optical Fiber Sensors

Structural Health Monitoring in Composite Structures: A Comprehensive Review

Robustness of Structural Health Monitoring Systems for Offshore Energy Structures based on Damage Characteristics

A Robust Lamb Wave Imaging Approach to Plate-Like Structural Health Monitoring of Materials with Transducer Array Position Errors

Rapid Multi-Damage Identification for Health Monitoring of Laminated Composites Using Piezoelectric Wafer Sensor Arrays

Acoustic monitoring of wind turbine blades using wavelet packet analysis and 1D convolutional neural networks

A hybrid wavelet-deep learning approach for vibration-based damage detection in monopile offshore structures considering soil interaction

Lamb wave-based damage detection of composite structures using deep convolutional neural network and continuous wavelet transform