Abstract:This work proposes and demonstrates a powder‐covering sintering strategy to prepare uniformly dense garnet type inorganic electrolyte ceramics. The key to realize uniformly dense effect lies on controlling the grains to be developed uniformly during sintering, which mainly results from narrow particle size distribution powder materials and small temperature difference. Highly uniformly dense garnet type solid‐state electrolyte plays a significant role in determining the performance of solid‐state lithium batteries. Herein, a rational powder‐covering sintering strategy is proposed and demonstrated, in which narrow‐particle‐size‐distribution fine powder and uniform sintering temperature distribution are considered as very significant factors. It is suggested that powder materials with wider particle size distribution dramatically decrease the densified level of electrolytes. Slow temperature elevating rate and the overhead structure of bearing table are found to be beneficial to uniform densification. Moreover, the uniform densification process of sintering solid‐state electrolyte is studied both microscopically and macroscopically, which can be divided into three phases according to the grain growing evolution and linear shrinkage patterns. The ionic conductivity of the as‐prepared Li6.4La3Zr1.4Ta0.6O12 (LLZTO) garnet electrolyte is determined to be 0.73 mS cm−1 at 303 K with an activation energy of 0.37 eV. The Li/LLZTO/Li symmetric cell exhibits a small interfacial impedance of 8.49 Ω cm2 and a high apparent critical current density of 2.15 mA cm−2 and also can be cycled for 1000 h continuously without short‐circuit. Such results indicate the good feasibility of as‐proposed sintering strategy to prepare uniformly dense garnet type solid‐state electrolytes for solid‐state lithium batteries.

Influence of Cold Sintering Process on the Structure and Properties of Garnet-Type Solid Electrolytes

Facile Surface Modification Method to Achieve an Ultralow Interfacial Resistance in Garnet-Based Li Metal Batteries

Low-Sintering-Temperature Garnet Oxides by Conformal Sintering-Aid Coating

Development of the Cold Sintering Process and Its Application in Solid-State Lithium Batteries

(Invited) Achieving High Areal Capacity and Extreme Critical Current Densities through Tailored Garnet Solid Electrolyte Structures

Cold Sintering of Li6.4La3Zr1.4Ta0.6O12/PEO Composite Solid Electrolytes

Cold sintering-enabled interface engineering of composites for solid-state batteries

Uniform Densification of Garnet Electrolyte for Solid‐State Lithium Batteries

Cold-sintering assisted process enables densified and robust fine-grained Li1.3Al0.3Ti1.7(PO4)3 electrolytes for solid-state batteries

Sintering Behavior of Garnet‐type Li6.4La3Zr1.4Ta0.6O12 in Li2CO3 Atmosphere and Its Electrochemical Property

Lithium dendrites suppressed by low temperature in-situ anti-perovskite coated garnet solid-state electrolyte

Li2CO3: A Critical Issue for Developing Solid Garnet Batteries

Broad temperature dependence, high conductivity, and structure-property relations of cold sintering of LLZO-based composite electrolytes

Unveiling the roles of alumina as a sintering aid in Li‐Garnet solid electrolyte

Insight into the Microstructure and Ionic Conductivity of Cold Sintered NASICON Solid Electrolyte for Solid-State Batteries

Enhanced densification and ionic conductivity of Li-garnet electrolyte: Efficient Li2CO3 elimination and fast grain-boundary transport construction

Low-Temperature Sintering of a Garnet-Type Li6.5La3Zr1.5Ta0.5O12 Solid Electrolyte and an All-Solid-State Lithium-Ion Battery.

A Sintering‐Free Cathode for Garnet‐Based All‐Solid‐State Li Metal Batteries

Liquid sintering of garnet electrolytes by lithium germanate: Properties and interfacial performance with lithium anode

Comprehensive Investigation into Garnet Electrolytes Toward Application-Oriented Solid Lithium Batteries

Microstructure and ionic conductivities of NASICON-type Li1.3Al0.3Ti1.7(PO4)3 solid electrolytes produced by cold sintering assisted process