Abstract:Solid-state lithium (Li) metal batteries are widely used due to their excellent safety, superior energy density, and low cost. Nevertheless, the practical application of solid-state Li batteries is hindered by the inferior ionic conductivity of the solid electrolyte and poor interface contact between the electrode and electrolyte. Herein, a flexible, hybrid ceramic-based electrolyte was fabricated by a solution-casting method using poly(vinylidene fluoride), Li1.4Al0.4Ti1.6(PO4)3 powders, and lithium bis(trifluoromethanesulfonyl)imide. To realize high ionic conductivity and a stable self-viscous electrode/electrolyte interfacial contact simultaneously, a mixed solution of 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide, lithium bis(trifluoromethanesulfonyl)imide, and fluoroethylene carbonate was introduced by the solution-infiltration method. The self-viscous Li1.4Al0.4Ti1.6(PO4)3 ceramic-based electrolyte exhibits superior ionic conductivity (2.4 × 10–4 S cm–1 at 25 °C), a high ionic transference number (0.42), wide voltage window (4.8 V vs Li/Li+), excellent thermal stabilities, and the ability to impede Li dendrite growth. In particular, the stable contact, low interfacial resistance, and fast ion-transport channels between the electrodes and solid electrolytes can be achieved by the self-viscous interfacial layer. The solid-state LiFePO4|Li battery assembled with the solid self-viscous electrolyte demonstrates a satisfactory initial discharge capacity of 138.0 mAh g–1 and capacity retention of 96.5% after 200 cycles at 0.5 C and under 25 °C. The self-viscous modification strategy of the solid electrolyte affords promising options for implementing the intimate electrode/electrolyte interfacial contact in high-energy-density solid-state batteries.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acs.energyfuels.1c01202.Figure S1: XRD patterns and SEM image of LATP ceramic powders. Figure S2: Temperature dependence of ionic conductivities for LATP pellets. Figure S3: Flexible and winding performances of self-viscous PLL-LEF electrolyte. Figure S4: Surface morphology of PL and PLL-LEF electrolytes. Figure S5: Adhesiveness exhibitions of PLL-LE composite electrolyte. Figure S6: EIS profiles of 10LiTFSI-40EMITFSI and 10LiTFSI-40EMITFSI-10FEC electrolytes. Figure S7: EIS profiles of stainless steel|PLL-LEF|Li cells. Figure S8: Thermogravimetry curve of PLL-LEF electrolyte. Figure S9: Flammability test of routine Celgard separator. Figure S10: EIS profiles of Li|PLL|Li cell for different aging times. Figure S11: Optical photographs of the PLL electrolyte. Figure S12: Ti 2p XPS of the PLL electrolyte. Figure S13: EIS profiles of Li symmetric cell with different electrolytes after cycling. Figure S14: Constant current cycling curves of Li|PLL-LEF|Li cells at 0.2 mA·cm–2. Figure S15: Constant current cycling curves of Li|PLL-LEF|Li cells at 0.5 mA·cm–2. Figure S16: Constant current cycling curves of Li|PLL-LEF|Li cells. Figure S17: High multiple SEM images of Li surfaces obtained from Li symmetrical cells. Figure S18: SEM image of pristine Li surface. Figure S19: EIS results of LiFePO4|PLL|Li, LiFePO4|PLL-LE|Li and LiFePO4|PLL-LEF|Li batteries. Figure S20: Typical charge–discharge voltage profiles of LiFePO4|PLL-LE|Li cell at 0.5 C. Figure S21: Electrochemical properties of Al2O3@LiNi0.5Co0.3Mn0.3O2|PLL-LEF|Li cell (PDF)This article has not yet been cited by other publications.

Interface engineering of Li<sub>1.3</sub>Al<sub>0.3</sub>Ti<sub>1.7</sub>(PO<sub>4</sub>)<sub>3</ sub> ceramic electrolyte via multifunctional interfacial layer for all-solid-state lithium batteries

Aqueous Tape Casting Phosphate Ceramic Electrolyte Membrane for High Performance All Solid-State Lithium Metal Battery

Engineering and regulating the interfacial stability between Li1.3Al0.3Ti1.7(PO4)3-based solid electrolytes and lithium metal anodes for solid-state lithium batteries

Interface Regulation Enabling Three-Dimensional Li1.3Al0.3Ti1.7(PO4)3-reinforced Composite Solid Electrolyte for High-Performance Lithium Batteries

Stabilizing LATP Electrolyte Interface of All-Solid-State Lithium Ion Batteries Consisting of High-Voltage Cathode

Recent Advances in Li1+xAlxTi2−x(PO4)3 Solid-State Electrolyte for Safe Lithium Batteries

Facile interfacial adhesion enabled LATP-based solid-state lithium metal battery

Construction of Polyvinylidene Fluoride Buffer Layers for Li1.3Al0.3Ti1.7(PO4)(3) Solid-State Electrolytes toward Stable Dendrite-Free Lithium Metal Batteries

Tailoring of Li/LATP-PEO Interface via a Functional Organic Layer for High-Performance Solid Lithium Metal Batteries

Building a Highly Functional Li1.3Al0.3Ti1.7(PO4)3/poly (vinylidene Fluoride) Composite Electrolyte for All-Solid-state Lithium Batteries

Stabilizing Li<sub>1.3</sub>Al<sub>0.3</sub>Ti<sub>1.7</sub>(PO<sub>4</sub>)<sub>3</ sub>|Li Metal Anode Interface in Solid-State Batteries by Kevlar Aramid Nanofiber-Based Protective Coating

Designing the Interface Layer of Solid Electrolytes for All‐Solid‐State Lithium Batteries

In Situ Gelation of a 1,3-Dioxolane Dual-Permeable Porous Tandem Framework with Excellent Interfacial Stability to Power Long-Cycling Solid-State Lithium Metal Batteries

Engineering Ferroelectric Interlayer between Li1.3Al0.3Ti1.7(PO4)3 and Lithium Metal for Stable Solid‐State Batteries Operating at Room Temperature

Polymer/ceramic interfacial layer enables stable cycling of all-solid-state Li-metal batteries with sulfide electrolyte

High-performance lithium metal batteries based on composite solid-state electrolytes with high ceramic content

An Ameliorated Interface Between PEO Electrolyte and Li Anode by Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 Nanoparticles

Insights into the Enhanced Interfacial Stability Enabled by Electronic Conductor Layers in Solid‐State Li Batteries

Asymmetric Solid-State Lithium-Metal-Battery Electrolytes Featuring Na Superionic Conductor-Type Ceramic and Garnet-Type Ceramic Filled Composite Polymer

Constructing Multifunctional Interphase between Li1.4Al0.4Ti1.6(PO4)(3) and Li Metal by Magnetron Sputtering for Highly Stable Solid-State Lithium Metal Batteries

Stabilizing Ceramic-Based Electrolyte Interfaces with Self-Viscous Modification Strategy for Solid-State Lithium Batteries