Abstract:The lack of comprehensive insight and accurate description on the dynamic thermomechanical behaviors in high-temperature and high-strain-rate loading environment could be one of the major obstacles to extend the laser metal deposited (LMD) Inconel 718 to engineering applications in aeroengine. In this study, to obtain in-depth understanding of plastic flow behavior of the LMD Inconel 718, uniaxial compressive experiments were conducted over a wide range of temperature (298-1273 K) and strain rate (0.001-5300/s). Based on a great number of experimental results, not only the anisotropy of compressive property, but the dependence of the plastic flow stress on temperature and strain rate were investigated systematically. The flow stress of the as deposited alloy in laser scanning direction is higher than that in depositing direction, which is attributed to the columnar grains epitaxially growing along the build direction and featuring the high length-diameter ratio within the as-deposited sample. Since the small-size precipitates in the under-aged (as-deposited) Inconel 718 alloy could be cut by the moving dislocations directly during plastic deformation, they have various effect on the interaction between moving dislocations and interstitial elements at different strain rate. The third-type of strain aging (3rd SA) effect, exhibiting an anomalous bell-shaped flow stress vs. temperature relation, was observed more apparently than that in the post-aged Inconel 718 reported by other literatures. As for the strain-rate effect, the flow stress of the alloy exhibits inconspicuous strain-rate sensitivity over the range of strain rate below similar to 10(3)/s, while increases sharply with the strain rate once it exceeds similar to 10(3)/s. Finally, taking into account the mechanical anisotropy, as well as the anomalous temperature and strain rate sensitivities of the flow stress, we developed a constitutive model based on a physical frame. In this model, an anisotropy component was introduced to consider the effective size of columnar grains in the corresponding loading direction, the strain rate hardening was enhanced as the strain rate gets close to a certain level, and a normal distribution with temperature was used to describe the 3rd SA effect. The developed model was shown to be able to accurately reproduce the plastic flow behavior of the LMD Inconel 718 over a wide range of temperature and strain rate.

Effect of Microstructures and Defects on Dynamic Compression and Shear Performance of Laser Metal-Deposited GH4169 Superalloy

Mechanical Properties and Fracture Behavior of Laser Powder-Bed-Fused GH3536 Superalloy

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Effects of Powder Feeding Rate on Microstructure and Mechanical Properties of GH4169

Effect of Material States on Microstructure and Properties of GH4169 Superalloy Laser-Welded Joint

Thermal deformation behavior and microstructure evolution of GH4169 superalloy under the shear-compression deformation conditions

Failure Behavior of Laser Metal Deposited Additive Manufacturing Ti-6Al-4V: Effects of Stress State and Initial Defects

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Effect of Laser Energy Density and Scanning Strategy on Residual Stress in Laser Melting Deposited FGH4096 Superalloy

Effect of microstructures on the high temperature stress rupture behavior of GTD222 superalloy prepared by selective laser melting

Mechanical Properties and Microstructure Evolution During Dynamic Compression and Cutting of Nickel-Based Superalloys

Competitive Fracture Mechanism and Microstructure‐Related Life Assessment of GH4169 Superalloy in High and Very High Cycle Fatigue Regimes

Distribution of Microstructure, Elastic Modulus and Residual Stress Near the Interface in Laser Repaired GH4169 Superalloy

Microstructural insights into fatigue short crack propagation resistance and rate fluctuation in a Ni-based superalloy manufactured by Laser powder bed fusion

Microstructure And Mechanical Properties Of Laser Melting Deposited Gh4169 Superalloy

Microstructure related failure mechanism of selective laser melted GH4169 with interior fatigue cracking

Influence of Energy Density on the Microstructure and Mechanical Properties of GH5188 Superalloy Formed by Laser Melting Deposition

Thermomechanical Behavior of Laser Metal Deposited Inconel 718 Superalloy over a Wide Range of Temperature and Strain Rate: Testing and Constitutive Modeling

Effects of Defects and Microstructures on Tensile Properties of Selective Laser Melted Ti6Al4V Alloys Fabricated in the Optimal Process Zone

Anisotropic dynamic compression response of an ultra-high strength steel fabricated by laser hybrid additive manufacturing

Comparison of surface integrity of GH4169 superalloy after high-energy, low-energy, and femtosecond laser shock peening