Abstract:Fabrication of miniaturized titanium thin-walled products directly using sheet metals is proven to be a promising approach with high productivity. In this process, however, there are many unknowns in terms of size effect and its affected fracture behavior. This study is thus aimed at investigating the effect of grain size on the fracture behavior of commercially pure titanium (CP-Ti) sheets with a thickness of 0.1 mm. Tensile tests combined with a digital image correlation (DIC) measurement system were conducted to determine the critical fracture stress of the specimens with different grain sizes. The fracture morphologies of the stretched specimens were further characterized by a scanning electron microscope (SEM). According to the experimental observation, an evident transition from ductile to brittle fracture as the grain size increases from 33.1 to 107.7 mu m is revealed. Macroscopically, the elongation and critical fracture stress decrease with the increase of grain size. While according to the microscopic observations, the number of dimples decreases with the increase of grain size. Meanwhile the cleavage planes and river patterns gradually appear in the coarse grain fracture surface. To explore the fracture mechanism, transmission electron microscope (TEM) observations were made utilizing the specimens with fine and coarse grains. Significant dislocation emission from crack-tips was revealed at different grain sizes. Moreover, evident dislocation pile-up at grain boundaries was observed in the specimen with a grain size of 33.1 mu m. Those intense dislocations reduce the effective stress at the crack tip resulting in higher crack propagation resistance. Nevertheless, the dislocation density at crack-tip decreases strongly with the increase of grain size leading to high crack-tip effective stress and less crack plasticity. Thus cleavage fracture was dominated in coarse grain CP-Ti sheets. A dislocation shielding model was developed to capture the dislocation observation in various grain sizes. The critical stress onset of CP-Ti sheets fracture during the tensile test was also predicted for validation.

Effect of grain size on high-temperature stress relaxation behavior of fine-grained TC4 titanium alloy

Influence of Grain Size on High-Temperature Compression Flow Behaviors of TC4 Titanium Alloy

Investigation on high-temperature stress relaxation behavior of Ti-6Al-4V sheet

Thermal relaxation of compressive residual stresses in surface gradient nanostructure of TC11 titanium alloy

Effect of Microstructure on Stress Relaxation Behavior of TC4 Alloy

Influence of Processing Factors on Stress Relaxation Behavior of TC4 Alloy

Research on stress relaxation behavior of TA15 titanium alloy

Effect of Grain Size and Testing Temperature on Low-Cycle Fatigue Behavior and Plastic Deformation Mode of Ti-2Al-2.5Zr

A Unified Constitutive Model of Stress Relaxation of Ti-6Al-4V Alloy with Different Temperatures from Elastic to Plastic Loading

Molecular dynamics simulations of polycrystalline titanium mechanical properties: Grain size effect

Effect Of Grain Size On The Superplastic Deformation Behavior Of Ti-55 Alloy

Study on Hot Deformation Behavior of Tc4 Titanium Alloy

Flow Behaviors and Dynamic Recrystallization Mechanisms Study of TC4 under Different Temperatures and Strain Rates

Stress Relaxation Behavior and Its Mechanism of BT14 Alloy with Equiaxed Grain

Effect of Grain Size on Twinning Behavior in Ti–2Al–2.5Zr Alloy Fatigued at 77K

Effects of grain size on the precipitation pathway and mechanical properties of (CoCrFeNi)94Ti2Al4 high entropy alloy

Thermal Deformation Behavior and Microstructural Evolution Mechanism of TC4 Titanium Alloy Based on Hot Processing Map

Behavior of Hot Deformation and its Effect Factors for TC4 Titanium Alloy

Relation Between Short-term Creep and Stress Relaxation of Titanium Alloy at High Temperature

Effect of grain size on the ductile-brittle fracture behavior of commercially pure titanium sheet metals

Investigation of hot deformation behavior and microstructure evolution of TC18 alloy and establishment of constitutive equation under friction-temperature correction