Abstract:In this study, shot peening (SP) treatment was implemented on a duplex (austenite and ferrite) stainless steel. By using X-ray diffraction residual stress determination and line profile analysis, the residual stress (including macro- and microstress) and microstructure evolutions in the surface layer of the shot peened material were discussed. Results pointed out that the initial thermal stress state were compressive (-80 MPa) in alpha phase and tensile (90 MPa) in gamma phase owing to the different thermal expansion coefficients of the two phases. After SP, the nonreversible plastic deformation of the surface layer and the interior of bulk was the main cause of the macrostresses. SP introduced more compressive residual stress into the gamma phase, the maximum compressive stress in gamma phase was similar to 1.3 times larger than that in alpha phase (-912 vs. -717 MPa) and occurred deeper in the sample interior (similar to 75 vs. 10 mu m). The inhomogeneous partitioning of the plastic strains, which was ascribed to the difference of the relative strength and deformation mechanism between the phases, was the contributing cause of microstresses. The average microstresses in surface layer of shot peened alloy were tensile in alpha phase and compressive in gamma phase, the magnitude of which changed with depth since the phase-specific plastic deformation was also a function of depth. The quantitatively microstructural analysis indicated that more deformation was stored in the gamma phase, the microstrain and dislocation density at the surface in gamma phase were about four and 2.6 times larger than that in alpha phase (7.25 vs. 1.83 x 10(-3), 3.9 vs. 1.5 x 10(15) m(-2)), respectively. Microhardness measurements showed that SP-induced work hardening was more evident in austenite, the hardness of austenitic phase was found significantly higher than that of ferritic phase in near surface region.

Residual Stress and Microstructure Characterization of 34crmo4 Steel Modified by Shot Peening

Corrosion Properties of 34CrMo4 Steel Modified by Shot Peening.

The influence of shot peening on mechanical properties, wear, and corrosion resistance of 42CrMo steel

Microstructural Evolution and Mechanical Response of the Surface of 18Crnimo7-6 Steel after Multistep Shot Peening During Annealing

Shot Peening Treatment and Characterization of 18CrNiMo7-6 Steel after Carburizing and Quenching

Residual Stress Relaxation and Micro-Structural Development of the Surface Layer of 18Crnimo7-6 Steel after Shot Peening During Isothermal Annealing

Micro-structure and Surface Layer Properties of 18Crnimo7-6 Steel after Multistep Shot Peening

INVESTIGATION OF SURFACE GRADIENT MICROSTRUCTURE OF SHOT PEENED S30432 STEEL BY X-RAY LINE PROFILE ANALYSIS METHOD

Effect Of Shot Peening On The Residual Stress And Mechanical Behaviour Of Low-Temperature And High-Temperature Annealed Martensitic Gear Steel 18crnimo7-6

Experimental Study on Macro- and Microstress State, Microstructural Evolution of Austenitic and Ferritic Steel Processed by Shot Peening

Investigation of Wet Shot Peening on Microstructural Evolution and Tensile-Tensile Fatigue Properties of Ti-6Al-4V Alloy

Residual Stress Distribution And Microstructure Characterization Of Particle Reinforced Titanium Matrix Composite After Shot Peening Treatment: A Review

Surface Modification of 304 Steel Using Triple-Step Shot Peening

Effect of Shot Peening on Residual Stress Distribution and Microstructure Evolution of Artificially Defected 50CrV4 Steel

The residual stress varying of shot peened TC4-DT titanium alloy

Experimental Research on Surface Shot Peening of 18Cr2Ni4WA Steel Gear

Microstructure of Gear Steels Treated by Shot Peening by X-Ray Line Profile Analysis Method

Investigation on Surface Characteristic and Tribological Behavior of BS960 Steel by Using Micro-shot Peening and Traditional Shot Peening

Residual stress and microstructure of the CNT/6061 composite after shot peening

Relation of Hardness with FWHM and Residual Stress of GCr15 Steel after Shot Peening

Characterization of Surface Modification of 347 Stainless Steel Upon Shot Peening