Abstract:Recently, as a two-dimensional (2D) material, black phosphorous (BP) has attracted more and more attention. However, few efforts have been made to investigate the BP/polyaniline (PANI) nanocomposite for ammonia (NH3) gas sensors. In this work, the BP/PANI nanocomposite as a novel sensing material for NH3 detection, has been synthesized via in situ chemical oxidative polymerization, which is then fabricated onto the interdigitated transducer (IDTs). The electrical properties of the BP/PANI thin film are studied in a large detection range from 1 to 4000 ppm, such as conduction mechanism, response, reproducibility, and selectivity. The experimental result indicates that the BP/PANI sensor shows higher sensitivity and larger detection range than that of PANI. The BP added into PANI, that may enlarge the specific surface area, obtain the special trough structure for gas channels, and form the p–π conjugation system and p–p isotype heterojunctions, which are beneficial to increase the response of BP/PANI to NH3 sensing. Meanwhile, in order to support the discussion result, the structure and morphology of the BP/PANI are respectively measured by Fourier transform infrared spectroscopy (FTIR), ultraviolet-visible spectroscopy (UV−vis), transmission electron microscopy (TEM), and field emissions scanning electron microscopy (SEM). Moreover, the sensor shows good reproducibility, and fast response and recovery behavior, on NH3 sensing. In addition, this route may offer the advantages of an NH3 sensor, which are of simple structure, low cost, easy to assemble, and operate at room temperature.

Enhanced Room-Temperature Ammonia-Sensing Properties of Polyaniline-Modified WO3 Nanoplates Derived Via Ultrasonic Spray Process

The Research and Application of Polyaniline/Multi-Walled Carbon Nanotubes Composite Sensitive Membrane for Ammonia Gas Detection

Vertically aligned PANI nanorod arrays grown on graphene oxide nanosheets for a high-performance NH3 gas sensor

Highly Stable Polyaniline-Poly(sodium 4-Styrenesulfonate) Nanoparticles for Sensing of Amines.

High Performance Gas Sensors Based on In-Situ Fabricated ZnO/polyaniline Nanocomposite: the Effect of Morphology on the Sensing Properties

Synthesis of different inorganic acids doped polyaniline materials and behavior of enhancing NH3 gas sensing properties

Composites of Fe2O3 Nanosheets with Polyaniline: Preparation, Gas Sensing Properties and Sensing Mechanism

Amino acids doped PANI sensitive materials for ammonia gas sensors operated at room temperature

Flexible Room Temperature Sensor with Modulation of Polyaniline Interfacial Polymerization by CTAB for Ppb-Level Ammonia Detection

Three-dimensional porous carbon framework coated with polyaniline for highly stable and selective ammonia sensing

Spray synthesis of rapid recovery ZnO/polyaniline film ammonia sensor at room temperature

PANI/3D crumpled Ti3C2TX/TiO2 nanocomposites for flexible conductometric NH3 sensors working at room temperature

Highly Sensitive NH3 Gas Sensors Based on Novel Polypyrrole-Coated SnO2 Nanosheet Nanocomposites

Design and preparation of hollow NiO sphere- polyaniline composite for NH3 gas sensing at room temperature

Pt/MoS2/Polyaniline Nanocomposite as a Highly Effective Room Temperature Flexible Gas Sensor for Ammonia Detection

1D/2D Heterostructured WS2@PANI Composite for Highly Sensitive, Flexible, and Room Temperature Ammonia Gas Sensor

Facile Synthesis of Polyaniline/Carbon-Coated Hollow Indium Oxide Nanofiber Composite with Highly Sensitive Ammonia Gas Sensor at the Room Temperature

Synthesis and characterization of highly sensitive ammonia sensor based on polyaniline/bismuth doped zinc oxide composites

Highly sensitive Cu-ethylenediamine/PANI composite sensor for NH3 detection at room temperature

High Sensitivity of Ammonia Sensor through 2D Black Phosphorus/Polyaniline Nanocomposite

In Situ Prepared Composite of Polypyrrole and Multi-Walled Carbon Nanotubes Grafted with Sodium Polystyrenesulfonate As Ammonia Gas Sensor with Wide Detection Range