Abstract:SnO2 has the advantages of excellent photostability and can be prepared at low-temperature below 200 ℃. It is regarded as one of the excellent materials for the electron transport layer, and widely used in efficient and stable planar heterojunction perovskite solar cells. In this work, the low-cost, dense and uniform SnO2 electron transport layer is prepared by spin coating at low temperature (150 ℃) for perovskite solar cells with a structure of FTO/SnO2/CH3NH3PbI3 (MAPbI3)/Spiro-OMeTAD/Au. The crystallization and photoelectric properties of SnO2 electron transport layers prepared at different concentrations (2.5%–10%) at 150 ℃, and the influences of SnO2 electron transport layers on the formation of perovskite films and the performances of perovskite solar cells are discussed. By analyzing the scanning electron microscope (SEM), ultraviolet-visible light absorption spectrum (UV-Vis) and transmission spectrum of the SnO2 film, it is found that the coverage and light transmittance of the substrate and band gap of the SnO2 film increase as the SnO2 content increases, while the absorbance decreases. By analyzing the SEM, UV-Vis, X-ray diffraction (XRD) and steady-state photoluminescence spectrum (PL) analysis of the SnO2/MAPbI3 thin film, it is found that the MAPbI3 deposited on the SnO2 layer with a concentration of 7.5% is uniform and pinhole-free, has the largest particle size and the best crystallinity, as well as more effective charge extraction capability and transport capability. By analyzing the electrochemical impedance (EIS) and external quantum efficiency (EQE) of the device, the SnO2 electron transport layer with a concentration of 7.5% has better interface contact and lower interface resistance, which is beneficial to reducing the recombination of carriers and improving the photoelectric conversion capability, The perovskite solar cells based on SnO2 layer prepared with a concentration of 7.5% reaches a photoelectric conversion efficiency of 15.82% (Voc = 1.06 V, Jsc = 21.62 mA/cm2, FF = 69.40%), After storing for 600 h in ambient air ((25±5) ℃, RH>70%) without encapsulation, its efficiency remains 92% of the initial efficiency. At the same time, we prepare flexible devices on flexible substrates (TIO/PEN) by using SnO2 precursor with a concentration of 7.5%, which exhibits good photovoltaic performance and achieves a photoelectric conversion efficiency of 13.12%, and storage time for 84 d in ambient air ((30±5) ℃, RH>70%) without encapsulation, its efficiency remains 48% of the initial efficiency. The PCE retains 78% of the initial efficiency after 1000 bending cycles with a bending radius of 3 mm. The study of optimizing the concentration of SnO2 has laid a foundation for improving the performance of flexible perovskite solar cells.

Introduction of LiCl into SnO2 electron transport layer for efficient planar perovskite solar cells

Enhancing Electron Extraction and Transport in Inorganic Perovskite Solar Cells Via Additional Built-in Potential of SnO2-BiFeO3 Nano-Heterostructure

Optimized SnO2 preparation and coherent interlayers for enhanced charge dynamics and efficient perovskite photovoltaics

Enhanced Electrons Extraction of Lithium-Doped SnO$_{2}$ Nanoparticles for Efficient Planar Perovskite Solar Cells

Enhanced performance of planar perovskite solar cells by doping the SnO2 electron transport layer with guanidinium chloride

NaCl-passivated and Na+-doped Tin Oxide Electron Transport Layers Enable Highly Efficient Planar Perovskite Solar Cells

Introduction of carbon nanodots into SnO2 electron transport layer for efficient and UV stable planar perovskite solar cells

Enhanced electron extraction using SnO2 for high-efficiency planar-structure HC(NH2)2PbI3-based perovskite solar cells

SnO2-Ti3C2 Blends As Electron Transport Layer for Efficient and Easily Fabricated Planar Perovskite Solar Cells

Electrochemical Reduction and Ion Injection of Annealing‐Free SnO2 for High Performance Perovskite Solar Cells

Enhancing efficiency of planar structure perovskite solar cells using Sn-doped TiO2 as electron transport layer at low temperature

TiO2/SnO2 Nanocomposites As Electron Transporting Layer for Efficiency Enhancement in Planar CH3NH3PbI3-Based Perovskite Solar Cells

Ionic liquid modified SnO2 nanocrystals as a robust electron transporting layer for efficient planar perovskite solar cells

Organic ammonium chloride salt incorporated SnO2 electron transport layer for improving performance of perovskite solar cells

A low-temperature TiO2/SnO2 electron transport layer for high-performance planar perovskite solar cells

TiO2/SnOxCly double layer for highly efficient planar perovskite solar cells

Poly(vinylpyrrolidone)-doped SnO2 as an electron transport layer for perovskite solar cells with improved performance

Heterovalent Samarium Cation‐Doped SnO2 Electron Transport Layer for High‐Efficiency Planar Perovskite Solar Cells

MDACl2-Modified SnO2 Film for Efficient Planar Perovskite Solar Cells

Reactive-Sputtered Prepared Tin Oxide Thin Film As an Electron Transport Layer for Planar Perovskite Solar Cells

Low-temperature Preparation of SnO<sub>2</sub> Electron Transport Layer for Perovskite Solar Cells