Abstract:In this work, the SnO 2 -Ti 3 C 2 hybrid electron transport layer (ETL) was prepared by incorporating two-dimensional Ti 3 C 2 -MXene into SnO 2 and appropriate ultraviolet (UV) ozone treatment. The synergistic effect of Ti 3 C 2 introduction and UV ozone treatment on the charge transport capacity of SnO 2 ETL, interface properties of ETL/perovskite, perovskite morphology, and device performance was systematically investigated. The results show that the introduction of Ti 3 C 2 does not affect the morphology and transmittance of SnO 2 ETL. The perovskite films based on SnO 2 -Ti 3 C 2 are not only dense, but also have smaller surface roughness, more uniform, and larger grain size, even penetrating the entire perovskite film. The surface oxidation of Ti 3 C 2 induced by UV-ozone treatment enhanced the charge transport capacity of ETL. The electron extraction and charge transfer at the interface between SnO 2 -Ti 3 C 2 ETL and perovskite are higher, and carrier recombination is effectively suppressed. Perovskite solar cells (PSCs) based on SnO 2 -Ti 3 C 2 ETL have larger charge recombination impedance and higher electron mobility, mainly due to enhanced ETL charge transport and optimization of interface properties. The short-circuit current ( J sc) and filling factor (FF) of PSCs are increased by 5% and 7% respectively, delivering a champion device with a relatively high FF of 79.38% and high power conversion efficiency of 19.52%, as well as good stability. Thus, this study provides a simple and effective method for the preparation of efficient and repeatable PSCs and paves the way for the industrialization of PSCs to a certain extent.

TiO2/SnOxCly double layer for highly efficient planar perovskite solar cells

Enhancing Electron Extraction and Transport in Inorganic Perovskite Solar Cells Via Additional Built-in Potential of SnO2-BiFeO3 Nano-Heterostructure

A low-temperature TiO2/SnO2 electron transport layer for high-performance planar perovskite solar cells

TiO2/SnO2 Bilayer Electron Transport Layer for High Efficiency Perovskite Solar Cells

SnO2-Ti3C2 Blends As Electron Transport Layer for Efficient and Easily Fabricated Planar Perovskite Solar Cells

Low Temperature Solution-Derived TiO2-SnO2 Bilayered Electron Transport Layer for High Performance Perovskite Solar Cells

TiO2/SnO2 Nanocomposites As Electron Transporting Layer for Efficiency Enhancement in Planar CH3NH3PbI3-Based Perovskite Solar Cells

High-effective SnO2-based perovskite solar cells by multifunctional molecular additive engineering

Enhanced electron extraction using SnO2 for high-efficiency planar-structure HC(NH2)2PbI3-based perovskite solar cells

TiO2 Phase Junction Electron Transport Layer Boosts Efficiency of Planar Perovskite Solar Cells

Preparation of TiO2/SnO2 Electron Transport Layer for Performance Enhancement of All-Inorganic Perovskite Solar Cells Using Electron Beam Evaporation at Low Temperature

Efficient planar heterojunction perovskite solar cells with enhanced FTO/SnO2 interface electronic coupling

Rational design of SnO 2 -based electron transport layer in mesoscopic perovskite solar cells: more kinetically favorable than traditional double-layer architecture

NaCl-passivated and Na+-doped Tin Oxide Electron Transport Layers Enable Highly Efficient Planar Perovskite Solar Cells

Synergetic Optimization of Upper and Lower Surfaces of the SnO2 Electron Transport Layer for High-Performance N-I-p Perovskite Solar Cells

Room-temperature processed TiO2 to construct composite electron transport layers for efficient planar perovskite solar cells

Tri-functionalized TiO Cl4-2 accessory layer to boost efficiency of hole-free, all-inorganic perovskite solar cells

Multi-cation hybrid stannic oxide electron transport layer for high-efficiency perovskite solar cells

SnO2-Based Perovskite Solar Cells: Configuration Design and Performance Improvement

Tin Oxide Bilayer as Effective Electron Transport Layers for Efficient and Stable Perovskite Solar Modules

Ionic liquid modified SnO2 nanocrystals as a robust electron transporting layer for efficient planar perovskite solar cells