Abstract:This study explores the influence of chemical composition and cooling rate on the microstructural formation of Al-based alloys, predominantly alloyed with Mn and Ce. Approximately 1 kg of the alloys with varying alloying element content was prepared in a protective resistance furnace. The solidified alloys were then sectioned into 100 g pieces, remelted, and cast into massive copper molds, resulting in samples with different thicknesses ranging from 0.3 to 6 mm. The cooling rates were precisely determined using numerical simulation, ranging from 10 3 to 10 4 K/s. The experimental results demonstrate that, at moderately high cooling rates (above 10 3 K/s), the primary intermetallics precipitated were identified as Al 20 Mn 2 Ce. However, at lower cooling rates, particularly when the Mn and Ce content were high, the formation of the "τ"-phase, Al 8 Mn 4 Ce, was observed and characterized by its detrimental dendrite-like morphology. Interestingly, as the cooling rate approached 10 5 K/s and in the presence of an optimal chemical composition (with sufficiently high Mn and Ce content), an amorphous structure formed at the outer surface of the samples. This amorphous structure exhibits intriguing potential for certain applications due to its unique properties. The desirable microstructure of bulk samples consists of submicron intermetallic compounds embedded in a boundary-free Al-matrix, which is promising for enhancing material strength and performance. This investigation sheds light on the crucial role of chemical composition and cooling rate in controlling the microstructural features of Al-based alloys, thereby providing valuable insights for the development of advanced materials with tailored properties for specific industrial applications. The role of rare earth metals (Ce and La) as poisoning and GFA (glass-forming ability) contributing elements is clarified. The Widmanstätten structure, appeared in the presence of high content of Mn, is discovered.

Interphase Boundary Segregation Induced Phase Transformation in a High-Pressure Die Casting Mg-Al-La-Ca-Mn Alloy

Microstructure Evolution and Properties of Mg-9Gd-0.8Al Alloy with Lamellar Phase During Extrusion at Different Temperatures

The Formation Mechanism of a Novel Interfacial Phase with High Thermal Stability in a Mg-Gd-Y-Ag-Zr Alloy

Elucidation of formation and transformation mechanisms of Ca-rich Laves phase in Mg-Al-Ca-Mn alloys

Solidification Microstructure Evolution in LA42 Mg Alloy under Various Cooling Rates

Construction and analysis of surface phase diagrams to describe segregation and dissolution behavior of Al and Ca in Mg alloys

Hierarchical phase separation behavior in a Ni-Si-Fe alloy

Phase transformation from phase to S phase at grain boundary during annealing in rapidly-solidified Al-Zn-Mg-Cu alloy

High Pressure Solidification Microstructure and Stability of Al-9.6%Mg Alloy

Directional Solidification and Microsegregation in a Magnesium-Aluminum-Calcium Alloy

Microstructure Formation of Al-Based Alloys in the Presence of Rare Earth Metals (Ce, La) and Mn under High Cooling Rate

Evolution of Deformation Substructure and MgxZnyCaz Metastable Phase in Fine-Grained Mg Alloys

Phase transformation from η phase to S phase at grain boundary during annealing in rapidly-solidified Al-Zn-Mg-Cu alloy

Interphase Boundary Segregation into an Ordered Core–Shell Structure with a Shell Containing Two Unit Cells

Microstructure and Mechanical Properties of Cast Al-Li-Mg Alloy: Role of Cu Addition and Heat Treatment

Structural transformation behavior in a high Nb–TiAl alloy additively manufactured by laser powder bed fusion

The Evolution and Characterizations of Al3(ScxZr1-x) Phase in Al–Mg-based Alloys Proceeded by SLM

Thermal Stability of Al–Mg Alloys after Solidification under High Pressures

In Situ Observation of Microstructure and Precipitate Phase Transformation during the Solidification of Mg‐Containing GH3625 Alloy at Different Cooling Rates

Strengthening Effect of Nano-Scale Precipitates in a Die-Cast Mg–4Al–5.6Sm–0.3Mn Alloy

The evolution of compositional and microstructural heterogeneities in a TaMo0.5ZrTi1.5Al0.1Si0.2 high entropy alloy