Abstract:Fully-transparent deep-sea pressure hulls have been attracted attention in recent years with the increasing demand for underwater observation. So far, public researches on design rule and failure modes for fully-transparent deep-sea pressure hulls are limited and the relevant experience cannot meet the requirements of new cabin design. In this study, the compression test is carried on, in which the material samples are subjected to quasi-static compressive load until failure in tests at different loading rates, and the hyperelastic finite element model is established in LS-DYNA software to simulate the failure process. Simulation results of material properties in finite element analysis on the cylindrical samples are compared with the experimental data, including the characteristic points of the mechanical properties in elastic stage and hardening stage, the ultimate load and failure mode of the samples. Mesh convergence analysis is conducted, and the appropriate mesh quality is accordingly selected in simulation of fully-transparent deep-sea pressure hulls. An equation for prediction of instability-type failure is described, which is derivation based on the classical analytical expression of elastic instability, thus, when 5 times of safety factor is taken, the wall thickness of the pressure hull is calculated to be t/R 0 = 0.0685 at 2,500 m depth. Ultimate strength and failure mode of a typical fully-transparent deep-sea pressure hull are simulated. First, the first-order linear buckling modal analysis is carried out to simulate initial geometric imperfections. Then, simulations for the loading and collapse process of two fully-transparent pressure hulls respectively with one opening and two openings are conducted, and the ultimate load of 126 MPa and 128 MPa for the two kinds of hulls are obtained. Finally, simulation of a scaled pressure hull is carried out and simulation results are compared with the experimental data in reference, which are basically consistent. The calculated failure strength shows that the spherical hulls satisfy the safety factor requirement of 5 times. The provided simulation procedure can be referred for failure analysis of fully-transparent pressure hulls.

Failure of Silicon Nitride Ceramic Flotation Spheres at Critical State of Implosion

Three Phases Fluid-Structure Interactive Simulations of the Deepsea Ceramic Sphere's Failure and Underwater Implosion

Numerical Study of Underwater Implosion of Spherical Pressure Hull on Deep-Sea Submersibles

Numerical Simulation and Analysis of the Underwater Implosion of Spherical Hollow Ceramic Pressure Hulls in 11000 M Depth

Numerical simulation and analysis of the underwater implosion of spherical hollow ceramic pressure hulls in 110 0 0 m depth

Additive Manufacturing of Silicon Nitride Ceramic Floatation Spheres with Excellent Mechanical Properties

Research on Characteristics of Deep-Sea Implosion Based on Eulerian Finite Element Method

Numerical Simulation and Analysis of the Chain-Reaction Implosions of Multi-Spherical Hollow Ceramic Pressure Hulls in Deep-Sea Environment

Underwater Implosion Protection of a New Concept Composite Structure for a Deep-Sea Hollow Ceramic Sphere with CFRP Shield

Fluid-structure Interaction of Spherical Pressure Hull Implosion in Deep-Sea Pressure: Experimental and Numerical Investigation

Numerical study of chain-reaction implosions in a spatial array of ceramic pressure hulls in the deep sea using a compressible multiphase flow model

Hydrostatic failure behavior of externally pressurized ceramic egg-shaped shells

Strength damage behavior analysis of silicon carbide(SiC) ceramic cylindrical shells under hydrostatic pressure based on the state-based peridynamics

Research on the Quasi-Static Collapse and Instantaneous Implosion of the Deep-Sea Spherical Pressure Hull

Dynamic Response Analysis of Spherical Pressure Hull Implosion Inside Adjacent Underwater Structure

Failure behavior of the ceramic thin-walled cylindrical shell under the hydrostatic pressure

Implosion Mechanisms of Metallic Cylindrical Shells Subjected to Combined Explosive Loading and Hydrostatic Pressure

Buckling and failure behavior of the silicon carbide (SiC) ceramic cylindrical shell under hydrostatic pressure

Review of Implosion Design Considerations for Underwater Composite Pressure Vessels

Insight into the Underwater Implosion Mechanisms of Thin-Walled Metallic Cylindrical Shells

Failure analysis on fully-transparent deep-sea pressure hulls used at 2,500 m depth