Abstract:The electrochemical nature of the contact firing reactions is studied by short‐circuiting the Ag fingers to the underlying Si emitter. The short‐circuit effect is gradually attenuated along the finger line away from the short‐spot owing to the ohmic drop of the electrode potential along the Si substrate. The contact quality is strongly correlated to the Ag crystallites formed on the emitter surface. The 6‐in full‐cell tests demonstrate that the segmentation of Ag fingers does not necessarily mitigate the short‐circuit effect. The "short‐circuit effect" in the fire‐through Ag metallization of crystalline Si (c‐Si) solar cells refers to the poor contact formation caused by an electrical short between the Ag gridline and underlying Si emitter during contact firing. This study employs two different Ag pastes containing PbO‐ and TeO2‐based glass frits to investigate the dependence of the short‐circuit effect on the length and pattern of the Ag finger lines. The results show that regardless of the employed glass frits, the short‐circuit effect is mitigated even near the short spot and gradually attenuated along the finger line away from the spot as the Ag finger line extends radially longer than the critical length (>35 mm). We demonstrate that this attenuation is independent of the finger line width and predominantly attributed to the ohmic drop of the electrode potential along the Si substrate. The results also show that, regardless of the glass frits, the contact quality is strongly correlated with the density of the Ag crystallites that are formed on the Si emitter surface. The 6‐in full‐cell tests indicate that the isolation of the short spots by segmenting the Ag finger lines does not necessarily result in the mitigation of the short‐circuit effect. We suggest that the reduction of Ag+ on the Si emitter surface should be the key process that must be controlled to achieve high‐quality contacts during contact firing, providing further insights into the electrochemical characteristics of contact firing reactions for the future development of Ag pastes.

Study on Tarnishing Mechanism of Grid Lines on Crystalline Silicon Solar Cells

Deterioration of Silver Alloy Electrode Caused by Photocatalytic Reaction for Crystalline Silicon Solar Cells

Improvement on Electrical Properties of Screen-Printed Crystalline Silicon Solar Cells by Light-Induced Electroplating of Silver

Improved Electrical Performance of Low-Temperature-Cured Silver Electrode for Silicon Heterojunction Solar Cells

Simulation, Experimental Evaluation, and Characterization of a Novel Grid Line Design for TOPCon Solar Cells With Reduced Silver Consumption

Formation of Nanostructured Emitter for Silicon Solar Cells Using Catalytic Silver Nanoparticles

Effect of Glass Frit Composition on Reliability of Silver Paste Metallization in Crystalline Silicon Solar Cells

An analytical investigation on characterizing the properties of glass composition for crystalline silicon solar cells based on the digital microsystem measurement technology

Attenuation of short‐circuit effect along screen‐printed silver gridlines during the contact firing process of crystalline silicon solar cells

Insight of Effect of Silver Powders on Silver‐silicon Contacts of Crystalline Silicon Solar Cells through Analysis of Glass Structural Decay

Interface Modeling Between the Printed Thick-Film Silver Paste and Emitter for Crystalline Silicon Solar Cells

Investigation of the mechanism of the Ag/SiNx firing-through process of screen-printed silicon solar cells

The Electrochemical Reactions in Crystalline Silicon Solar Modules

The Modulation of Surface Texture for Single-Crystalline Si Solar Cells Using Calibrated Silver Nanoparticles As a Catalyst

Mechanism of Silver/glass Interaction in the Metallization of Crystalline Silicon Solar Cells

Study on the Front Contact Mechanism of Screen-Printed Multi-Crystalline Silicon Solar Cells

Fabrication of Metal Grid on Silicon-Based Solar Cell by Electrochemical Deposition and Microcontact Print

Effects of Silver Nanoparticles on the Firing Behavior of Silver Paste on Crystalline Silicon Solar Cells

Impact of Interface Microstructure on Adhesion Force Between Silver Paste and Silicon Solar Cells’ Emitter

Application of CTLM Method Combining Interfacial Structure Characterization to Investigate Contact Formation of Silver Paste Metallization on Crystalline Silicon Solar Cells