Abstract:Bulk-form nanocomposites of TiC-reinforced 316L stainless steel matrix were fabricated by selective laser melting (SLM), an emerging powder-bed additive manufacturing technique which allows the direct fabrication of usable end-products, using various volumetric laser energy densities (a). The microstructural features of the distribution and sizes of TiC nanoparticles, as well as the grain sizes and tribological performances of the SLMprocessed nanocomposite parts, were sensitive to the applied eta. Increasing eta enhanced the dispersion state of nanoscale TiC owing to intensified Marangoni flow and the corresponding capillary force, which prevented TiC aggregation and promoted a uniform dispersion of reinforcements in the solidified matrix. However, with increasing eta, the TiC particle size also increased, and some nanoparticles lost their initial nanostructure because of significant thermal accumulation within the molten pool. Increasing eta also caused increases in the grain sizes of the fabricated nanocomposite because of the decreasing cooling rate. A simulation model was developed to enhance understanding of the manufacturability of these new materials, as well as to predict the temperature evolution and thermal behaviors of the molten pool under various eta. The simulation modeled the effects of various eta values on the temperature distribution evolutions and the corresponding effects of Marangoni convection during the SLM process. The temperature distribution was significantly influenced by the applied a; the maximum temperature gradient within the molten pool was increased significantly with increased a. The simulation results validated the experimental results and the underlying physical mechanism of the molten pool. The microhardness of the SLM nanocomposite decreased sharply with increased grain size due to the lower cooling rate, but increased with further increases in eta because of the enhanced densification degree. Nanocomposites processed under the optimum condition of eta = 200 J/mm(3) showed the lowest wear rates accompanied by the formation of adherent and strain-hardened tribolayers on the worn surfaces of the nano composites, suggesting improved tribological performance.

Selective Laser Melting of TiN Nanoparticle-Reinforced AlSi10Mg Composite: Microstructural, Interfacial, and Mechanical Properties

Simultaneous Enhancement of Strength, Ductility, and Hardness of TiN/AlSi10Mg Nanocomposites Via Selective Laser Melting

Selective Laser Melting of Nano-Tin Modified AlSi10Mg Composite Powder with Low Laser Reflectivity

Microstructure and Mechanical Behavior of TiCN Reinforced AlSi10Mg Composite Fabricated by Selective Laser Melting

Microstructure, solidification behavior and mechanical properties of Al-Si-Mg-Ti/TiC fabricated by selective laser melting

Microstructure evolution and mechanical properties of selective laser melting fabricated hybrid particle reinforced AlSi10Mg composites

Selective Laser Melting of Nano-Tib2 Decorated Alsi10mg Alloy with High Fracture Strength and Ductility

Microstructural evolution and mechanical performance of in-situ TiB2/AlSi10Mg composite manufactured by selective laser melting

Selective laser melting of TiB2/AlSi10Mg composite: Processability, microstructure and fracture behavior

In-situ preparation and formation of TiB/Ti-6Al-4V nanocomposite via laser additive manufacturing: Microstructure evolution and tribological behavior

Selective laser melting of TiB<sub>2</sub>/AlSi10Mg composite: Processability, microstructure and fracture behavior

Effect of nano-TiB2 particles on the anisotropy in an AlSi10Mg alloy processed by selective laser melting

Thermal evolution behavior and fluid dynamics during laser additive manufacturing of Al-based nanocomposites: Underlying role of reinforcement weight fraction

Selective Laser Melting of High-Strength TiB2/AlMgScZr Composites: Microstructure, Tensile Deformation Behavior, and Mechanical Properties

Interfacial structures and strengthening mechanisms of in situ synthesized TiC reinforced Ti6Al4V composites by selective laser melting

Microstructure, Mechanical Properties and Fracture Behavior of Micron-Sized TiB2/AlZnMgCu(Sc,Zr) Composites Fabricated by Selective Laser Melting

Effects of Micron/Submicron TiC on Additively Manufactured AlSi10Mg: A Comprehensive Study from Computer Simulation to Mechanical and Microstructural Analysis

Microstructure evolution and mechanical properties of Al-Al2O3 composites fabricated by selective laser melting

Rapid Fabrication of TiN/AISI 420 Stainless Steel Composite by Selective Laser Melting Additive Manufacturing

Thermal Behavior of the Molten Pool, Microstructural Evolution, and Tribological Performance During Selective Laser Melting of TiC/316L Stainless Steel Nanocomposites: Experimental and Simulation Methods

Investigation on the Microstructure and Mechanical Properties of CNTs-AlSi10Mg Composites Fabricated by Selective Laser Melting