Abstract:In order to investigate the effect of TiB2 contents on the microstructure and wear resistance of titanium matrix composites, commercial pure Ti (CP-Ti) powders with 0–7.5 wt.% TiB2 particles were melted by selective laser melting (SLM) to produce the in-situ Ti-TiB composites. When the TiB2 content increases from 2.5 wt.% to 7.5 wt.%, the microstructures of the Ti-TiB composites undergo a transition from the single phase of α′-Ti to the mixed phases of α′-Ti, TiB and TiB2, and the acicular α′-Ti is refined significantly from 1.03 ± 0.24 μm to 0.36 ± 0.05 μm, showing that increasing the TiB2 content induces the formation of TiB and refines the microstructure. Moreover, large TiB2 particles are not melted completely and they react with the Ti matrix liquid to form a TiB layer around the Ti matrix during SLM. However, small TiB2 particles are completely dissolved into the Ti matrix liquid so that the eutectic TiB grains are precipitated at the boundaries of the Ti matrix after in-situ reaction of TiB2 with Ti. The formation of α′ martensite in the titanium matrix and the addition of TiB2 can induce the fine grain strengthening, the dispersion strengthening, the solid solution strengthening in the SLM-produced composites. The results indicate that the microhardness of the composites increases from 258 ± 10.3 HV0.2 to 435 ± 14.7 HV0.2. The wear process of the SLM-produced CP-Ti and TiB2 reinforced Ti matrix composites is accompanied by adhesion wear, abrasive wear and oxidation wear. As a result, when the TiB2 content increases to 7.5%, the wear resistance of the composites increases by 32.6% compared with that of the CP-Ti. These improvements are mainly due to strengthening and hardening effects induced by TiB2 particles and refinement of Ti matrix. This study provides some basis for developing wear-resistant and high-strength titanium alloys.

In-situ preparation and formation of TiB/Ti-6Al-4V nanocomposite via laser additive manufacturing: Microstructure evolution and tribological behavior

Microstructure and Wear-resistant Properties of in situ TiB-TiC Reinforced Titanium Matrix Composites by Laser Deposition Manufacturing

Microstructure Evolution and Mechanical Properties of Selective Laser Melted Bulk-Form Titanium Matrix Nanocomposites with Minor B4C Additions

Microstructural evolution and mechanical performance of in-situ TiB2/AlSi10Mg composite manufactured by selective laser melting

Nano-TiB Whiskers Reinforced Ti–6Al–4 V Matrix Composite Fabricated by Direct Laser Deposition: Microstructure and Mechanical Properties

Microstructure and mechanical properties of (TiB+TiC)/Ti composites fabricated in situ via selective laser melting of Ti and B4C powders

Refined microstructure and enhanced wear resistance of titanium matrix composites produced by selective laser melting

Interfacial structures and strengthening mechanisms of in situ synthesized TiC reinforced Ti6Al4V composites by selective laser melting

Investigation on Microstructures and Mechanical Behavior of In-Situ Synthesized TiC and TiB Reinforced Ti6Al4V Based Composite

In-situ synthesis of Ti<sub>5</sub>Si<sub>3</sub>-reinforced titanium matrix nanocomposite by selective laser melting: Quasi-continuous reinforcement network and enhanced mechanical performance

Selective Laser Melting of TiN Nanoparticle-Reinforced AlSi10Mg Composite: Microstructural, Interfacial, and Mechanical Properties

Simultaneous Enhancement of Strength, Ductility, and Hardness of TiN/AlSi10Mg Nanocomposites Via Selective Laser Melting

Study on Manufacturing Processes and Properties of TiB2 Reinforced Al-Si Composite by Laser Additive Manufacturing

Effect of TiB2 Content on Microstructure and Properties of In-Situ TiB/Ti6Al4V Composites

Mechanical Properties of In-Situ Synthesis of Ti-Ti3Al Metal Composite Prepared by Selective Laser Melting

Microstructure and tribological properties of laser in-situ synthesized Ti3Al composite coating on Ti-6Al-4V

Microstructure and Tribological Behavior of in Situ Synthesized (tib+tic)/ti6al4v (tib/tic=1/1) Composites

Selective laser melting of TiB<sub>2</sub>/AlSi10Mg composite: Processability, microstructure and fracture behavior

On the Microstructure, Mechanical Properties and Wear Resistance of an Additively Manufactured Ti64/metallic Glass Composite

Microstructure evolution and mechanical properties of selective laser melting fabricated hybrid particle reinforced AlSi10Mg composites

Effect of In-Situ TiB2 Particles on Microstructure and Mechanical Properties of Al–Fe–Ni Manufactured by Selective Laser Melting