Abstract:The thermal conversion of waste plastic products can provide a promising solution to the issues of environmental pollution, waste management, and energy needs. However, our present understanding on the thermal reforming of different kinds of plastic wastes mixtures during their co-pyrolysis and co-gasification for syngas production and energy recovery is insufficient. Non-selective urban polypropylene (PP) and polystyrene (PS) waste plastics were chosen for the investigations reported here. Thermal degradation properties of PP and PS as well as their blends in different mass ratios were investigated via thermogravimetric (TG) analysis. Co-pyrolysis and CO 2 -assisted co-gasification of PP-PS blends were then conducted using a fixed-bed reactor at a temperature of 1173 K. Experimental results from the blends were then compared with the weighted value calculated from their component feedstocks to quantify the degree of synergistic effect. TG results showed that the co-treatment of PP and PS enhanced the respective devolatilization process. The co-pyrolysis of PP and PS enhanced their thermal cracking, leading to synergistic increases in the yields of H 2 , light hydrocarbons (HC) and total syngas. In co-gasification, the reforming reaction involving CO 2 was synergistically enhanced, resulting in the increased yields of H 2 and HC. The gasification reactivity of carbon black improved during the co-processing of PP and PS due to the synergistic effect between the two different kinds of plastics. Higher synergistic effects were observed from the plastic mixtures having higher PS content that resulted in increased yield of syngas. Co-gasification of PP-PS blends having 40% PP content (2P3S) exhibited the maximum synergistic effect on H 2 , CO, and total syngas showing increased yields by 88.8%, 77.7%, and 74.2% respectively. The lowest synergistic effect was observed for HC that showed increased yield of only 25.1%. The optimal CO 2 consumption was also observed from the co-gasification of 2P3S. Each gram of 2P3S feedstock consumed approximately 1.80 g of CO 2 to result in highest recovered energy of 27.49 kJ/g and the maximum overall energy efficiency of 43.2%. The results revealed that enhanced thermal cracking and CO 2 reforming reaction, along with the improved reactivity of carbon black were mainly responsible for increased yields of H 2 , HC, CO and total syngas during co-gasification. This study contributes to the fundamental understanding of co-processing of non-separated waste plastics for enhanced syngas production and energy recovery, elucidating the synergistic effect between the various kinds of plastics during their co-pyrolysis and co-gasification.

Co-gasification of Plastic Wastes and Soda Lignin in Supercritical Water

Supercritical water Co-gasification of biomass and plastic wastes for hydrogen-rich gas production using Ni-Cu/AC-CaO catalyst

Experimental study on CO 2 co-gasification characteristics of biomass and waste plastics: Insight into interaction and targeted regulation method

Microscopic mechanism for CO 2 -assisted co-gasification of polyethylene and softwood lignin: A reactive force field molecular dynamics study

Synergistic effects during co-pyrolysis and co-gasification of polypropylene and polystyrene

Research on co-gasification of polyethylene and cellulose via reactive molecular dynamics simulation

Synergistic interactions between cellulose and plastics (PET, HDPE, and PS) during CO2 gasification-catalytic reforming on Ni/CeO2 nanorod catalyst

Synergistic Effect and Chlorine-Release Behaviors During Co-pyrolysis of LLDPE, PP, and PVC

Study on the mechanisms of hydrogen production from alkali lignin gasification in supercritical water by ReaxFF molecular dynamics simulation

Supercritical water co-gasification of waste R134a and plastics to produce valuable chemicals and fuels: ReaxFF reactive molecular dynamic simulation

Revealing the mechanism on steam co-gasification of cellulose and polyethylene: A combined ReaxFF and DFT study

Hydrothermal Liquefaction of Plastics: a survey of the effect of reaction conditions on the reaction efficiency.

Experimental Investigation on Chemical Looping Co‐gasification of Water Hyacinth and Solid Wastes

Exploration on the steam gasification mechanism of waste PE plastics based on ReaxFF-MD and DFT methods

Assessment of Supercritical Water Gasification of Food Waste under the Background of Waste Sorting: Influences of Plastic Waste Contents

Development of integrated reactive system based on co-combustion of wood biomass and plastic: Efficient hydrogen and methane production

Facilitation of coke gasification by coking wastewater and its degradation properties in thermochemical reactions

Preparation of monocyclic aromatic hydrocarbons from industrial lignin residue and polyethylene co-pyrolysis by microwave-assisted in fluidized bed based on bimetal-loaded HZSM-5/MCM-41 core-shell catalyst

Direct numerical simulations of polypropylene gasification in supercritical water

Sorption-enhanced Chemical Looping Steam Reforming Coupled with Water Splitting for Syngas and H2 Coproduction Using Waste Plastic As Fuel

STUDY ON CO-GASIFICATION OF SLUDGE AND COAL IN SUPERCRITICAL WATER