Abstract:The complex three-shaft three-reducer structural designs of helicopter transmission systems are prone to changes in the relative positions of shafting under the conditions of main rotor and tail rotor loads. These changes will affect the transmission characteristics of the entire transmission system. In this study, the planetary gear trains of helicopters were examined. Due to the fact that these structures are considered to be the most representative structures of the main reducers of helicopters, they were selected as the study objects for the purpose of examining the meshing characteristics of planetary gear trains when the relative positions of the shafting changed due to the position changes of the main rotor shafts under variable load conditions. It was found that by embedding the comprehensive time-varying meshing stiffness values of the main rotor shafts at different positions, a dynamic model of the relative position changes of the planetary gear trains could be established. Then, combined with the multibody dynamics software, the meshing characteristics of the sun gears, and the planetary gears, the planetary gears and the inner ring gears were simulated and analyzed under different inclinations and offsets of the shafting. The results obtained in this study revealed the following: (1) the average meshing force of the gears increased with the increases in the angle inclinations, and the meshing force between the sun gears and the planetary gears increased faster than the meshing force between the planetary gears and the inner ring gears. It was observed that during the changes in the shafting tilt positions, obvious side frequency signals had appeared around the peak of the meshing frequency in the spectrum. Then, with the continuous increases in the tilt position, the peak was gradually submerged; (2) the average meshing force of the gears increased with the increases in the offset, and the increasing trend of the meshing force between the sun gears and the planetary gears was similar to that observed between the planetary gears and the inner ring gears. It was found that when the shafting offset position changed, there were obvious first and second frequency doubling in the spectrum; (3) the mass center orbit radii of the sun gears increased with the increases in the shafting position changes, and the changes in the angular tilt position were found to have greater influencing effects on the mass center orbit radii of the sun gears than the changes in the offset positions. This study’s research findings will provide a theoretical basis for future operational status monitoring of the main transmission systems of helicopters and are of major significance for improvements in the operational stability of helicopter transmission systems, which will potentially ensure safe and efficient operations.

Fault Characteristics Analysis of Planetary Gear of Helicopter Main Reducer

Load sharing analysis and reliability prediction for planetary gear train of helicopter

An Analysis of the Gear Meshing Characteristics of the Main Planetary Gear Trains of Helicopters Undergoing Shafting Position Changes

Characteristics analysis of the new flexible ring gear for helicopter reducer

Nonlinear dynamic modeling and analysis of a helicopter planetary gear set for tooth crack diagnosis

Research Advances of Fault Diagnosis Technique for Planetary Gearboxes

Dynamic Analysis of a Fault Planetary Gear System under Nonlinear Parameter Excitation

Fault feature analysis of planetary gear set influenced by cracked gear tooth and pass effect of the planet gears

Condition monitoring and fault diagnosis of planetary gearboxes: A review

Study on nonlinear vibration and primary resonance characteristics of helicopter face gear-planetary gear coupling transmission system

Fault identification method for planetary gear based on DT-CWT threshold denoising and LE

Analysis of Inherent Characteristics of Two-Speed Planetary Gear Transmission System

Dynamic modeling and analysis of multistage planetary gear system considering tooth crack fault

Maximum Correlated Kurtosis Deconvolution and Overlapping Group Shrinkage Denoising for Incipient Fault Diagnosis of Helicopter Planetary Gear Train

Fault Detection of Planetary Gearboxes Using New Diagnostic Parameters

Reliability Design of Two-Stage Planetary Gear Wheel Hub Reducer based on Multi-Objective Optimization

A Time-Frequency Analysis Approach Based On Plane Partition For Fault Diagnosis Of The Planetary Gearbox Under Nonstationary Conditions

Research of Planetary Gear Fault Diagnosis Based on Multi-Scale Fractal Box Dimension of Ceemd and Elm

A method of health monitoring on helicopter speed reducer based on FMECA

Vibration Signal Simulation and Fault Diagnosis of Planetary Gearboxes Based on Transmission Mechanism Analysis

Amplitude Demodulation Analysis for Fault Diagnosis of Planetary Gearboxes