Abstract:Background Driven by emission regulations, the technology of emission control catalysts has been under increasing need for development. Understanding the deactivation mechanism of aged or spent automobile exhaust catalysts is the key to extending their service lifetime. However, the lack of comprehensive microstructural characterization results in an incomplete understanding of their physicochemical properties. Deactivation mechanism of automobile exhaust catalysts is a considerably complex phenomenon, it can be classified into three groups based on its origin: thermal sintering, chemical poisoning and mechanical deactivation. Results In this study, an aged high-mileage automobile exhaust catalyst with Pd and Rh active phases supported on a cerium zirconium oxide–doped alumina coating on cordierite was analysed; six consecutive monolithic blocks along the inlet to the outlet of the aged catalyst were extracted, and the corresponding metallographic samples were fabricated using the vacuum impregnation resin method. The purpose of this study was to accurately characterize the different regions of the monolith via electron probe microanalysis and to infer potential causes of catalyst deactivation. Two major causes of deactivation were found: (1) aggregation and alloying of precious-metal particles caused by thermal sintering and (2) chemical poisoning caused by sulphur and phosphorus. Other mechanisms, such as mechanical degradation, which mainly manifests as the loss or wear of the washed coating, were also found to be involved in deactivation. Additionally, the catalytic activity tests showed a considerable decrease in the aged catalyst. The poison concentration trends in the washcoat indicated that P is detrimental to CO oxidation, while S accumulation affects propane oxidation. Significance This analysis method can be of substantial practical significance in developing advanced washcoat materials. Meanwhile, it has great potential in the washcoat analysis of honeycomb-shaped monolithic catalyst, such as natural gas catalyst, diesel vehicle oxidation catalyst and other honeycomb catalysts applied in chemical industry.

A New Methodology for Washcoat Analysis of Honeycomb-shaped Monolithic Catalysts Using Scanning Electron Microscopy and Energy-Dispersive X-ray Analysis

Nickel Nanoparticles Embedded in Porous Carbon-Coated Honeycomb Ceramics: A Potential Monolithic Catalyst for Continuous Hydrogenation Reaction

Synthesis and Characterization of H-2 Combustion Monolithic Catalyst Based on Mesoporous Mgal2o4 Spinel Coating

Synthesis and Characterization of H2 Combustion Monolithic Catalyst Based on Mesoporous MgAI204 Spinel Coating

Preparation and properties of washcoats for three way catalyst

Preparation and characterization of a novel washcoat material and supported Pd catalysts

Structure characterization of aged automobile exhaust catalysts using electron probe microanalysis

Mechanical Stability of Monolithic Catalysts: Factors Affecting Washcoat Adhesion and Cohesion During Preparation

Preparation and Performance Evaluation of Honeycomb Catalysts

Development of a centrifugal coating method to load catalyst washcoat onto porous substrates with high uniformity and adhesive strength

Preparation Method Study On Pd/Ce/Al/Monolith Honeycomb Catalyst

Preparation, Characterization and Effect of Ce-Zr Washcoat on Zn-Cr Monolithic Catalysts for Methanol Autothermal Reforming

Mass Transport in Nanoarray Monolithic Catalysts: an Experimental-Theory Study

Preparation of Pd/α-Al_2O_3 Honeycombs for Catalytic Lean Burn of CH_4

Ultrathin Washcoat and Very Low Loading Monolithic Catalyst with Outstanding Activity and Stability in Dry Reforming of Methane

Mass Transfer Enhancement and Drying Mechanism of High Adhesion Saturated Impregnated Co-Al2O3 Monolithic Catalyst

Effects of Slurry Composition and Interfacial Adhesion of Monolithic Coatings on FeCrAl Honeycombs

Mechanical Stability of Monolithic Catalysts: Improving Washcoat Adhesion by FeCrAl Alloy Substrate Treatment

Investigation of Hydrogenation and Mass Transfer Performance in Micropacked Beds with Highly Active Monolithic Catalysts

Study on loading of γ-alumina washcoat on FeCrAl metallic honeycomb support

Characterization of Electrodeposited Porous Structured Composite Layers and Their Unconventional Wettability Properties