Abstract:Purpose This study aims to investigate the machining performance of CVD-coated carbide tools by considering most crucial machinability aspects: cutting force, tool life, surface roughness and chip morphology in high-speed hard turning of AISI 4340 alloy steel under a sustainable minimum quantity lubrication (MQL) environment. Design/methodology/approach The purpose of this study is to analyze the performance of coated carbide tools under MQL environment therefore, machining tests were performed in accordance with the Taguchi L9 orthogonal array, accommodating the three crucial machining parameters such as cutting speed (V = 300–400 m/min), feed rate (F = 0.1–0.2 mm/rev) and depth of cut (DOC = 0.2–0.4 mm). The measured or calculated values obtained in each experimental run were validated for normality assumptions before drawing any statistical inferences. Taguchi signal-to-noise (S/N) ratio and analysis of variance methodologies were used to examine the effect of machining variables on the performance outcomes. Findings The quantitative analysis revealed that the depth of cut exerted the most significant influence on cutting force, with a contributing rate of 60.72%. Cutting speed was identified as the primary variable affecting the tool life, exhibiting a 47.58% contribution, while feed rate had the most dominating impact on surface roughness, with an overall contributing rate of 89.95%. The lowest cutting force (184.55 N) and the longest tool life (7.10 min) were achieved with low machining parameters at V = 300 m/min, F = 0.1 mm/rev, DOC = 0.2 mm. Conversely, the lowest surface roughness (496 nm) was achieved with high cutting speed, low feed rate and moderate depth of cut at V = 400 m/min, F = 0.1 mm/rev and DOC = 0.3 mm. Moreover, the microscopic examination of the chips revealed a serrated shape formation under all machining conditions. However, the degree of serration increased with an incremental raise with cutting speed and feed rate. Research limitations/implications The study is limited to study the effect of machining parameters within the stated range of cutting speed, feed rate and depth of cut as well as other parameters. Practical implications Practitioners may consider to adopt this machining technique to create more sustainable working environment as well as eliminate the disposal cost of the used metal cutting fluid. Social implications By applying this machining technique, diseases caused by metal cutting fluid to the mechanist will be significantly reduced, therefore creating better lifestyles. Originality/value Hard turning is commonly carried out with advanced cutting tools such as ceramics, cubic boron nitride and polycrystalline cubic boron nitride to attain exceptional surface finish. However, the high cost of these tools necessitates exploration of alternative approaches. Therefore, this study investigates the potential of using cost-effective, multilayer-coated carbide tools under MQL conditions to achieve comparable surface quality. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-01-2024-0013/

Machining characteristics based life cycle assessment in eco-benign turning of pure titanium alloy

Life cycle assessment of sustainable turning techniques for pure titanium alloy: a comparative analysis

Sustainability Assessment Comparison of Cutting Fluid for Turning of Titanium Alloy Grade II

Machining grade 4 titanium alloy by minimum quantity lubrication for enhanced sustainable manufacturing

A Study on the Machinability of Environmentally Friendly Turning of Titanium Grade 2 Alloy

Machining performance and sustainability analysis of Al2O3-CuO hybrid nanofluid MQL application for milling of Ti-6Al-4V

Investigation of the Effects of Cutting Fluid Application with Minimum Quantity Lubrication (MQL) Method on the Machinability of Pure Titanium

Effect of Minimum Quantity of Lubricant on Carbide Tools and Surface Integrity in the Machining of Titanium Aluminides

Sustainable milling of Ti–6Al–4V: A trade-off between energy efficiency, carbon emissions and machining characteristics under MQL and cryogenic environment

High-speed turning of AISI 4340 alloy steel using carbide tools in a sustainable minimum quantity lubrication environment

Sustainability assessment associated with surface roughness and power consumption characteristics in nanofluid MQL-assisted turning of AISI 1045 steel

The machinability of titanium alloy thin-wall parts in cooling minimum quantity lubrication (CMQL) environments

Optimization of process parameters for turning of titanium alloy (Grade II) in MQL environment using multi-CI algorithm

Comparison of Tool Wear, Surface Morphology, Specific Cutting Energy and Cutting Temperature in Machining of Titanium Alloys Under Hybrid and Green Cooling Strategies

Research on Tool Wear and Machining Characteristics of TC6 Titanium Alloy with Cryogenic Minimum Quantity Lubrication (CMQL) Technology

Performance and Life Cycle Analysis of Soybean Oil-Based Minimum Quantity Lubrication in Machining of Ti6Al4V

Towards sustainable manufacturing: Multiple optimization of surface roughness [math], flank wear [math] in MQL-assisted milling of Titanium Alloy Ti-6Al-4V

Sustainability Assessment and Machinability Investigation of Austenitic Stainless Steel in Finish Turning with Advanced Ultra-Hard SiAlON Ceramic Tool under Different Cutting Environments

Sustainable Lubrication Methods for the Machining of Titanium Alloys: An Overview

Tribology and machinability performance of hybrid Al2O3 -MWCNTs nanofluids-assisted MQL for milling Ti-6Al-4 V

Minimal quantity cooling lubrication in turning of Ti6Al4V: Influence on surface roughness, cutting force and tool wear