Abstract:The modeling of stator and rotor faults is the basis of the development of online monitoring techniques. To obtain reliable stator and rotor fault models, this paper focuses on dynamic modeling of the stator and rotor faults in real-time, which adopts a multiple-coupled-circuit method by using a winding function approach for inductance calculation. Firstly, the model of the induction machine with a healthy cage is introduced, where a rotor mesh that consists of a few rotor loops and an end ring loop is considered. Then, the stator inter-turn fault model is presented by adding an extra branch with short circuit resistance on the fault part of a stator phase winding. The broken rotor bar fault is then detailed by merging and removing the broken-bar-related loops. Finally, the discrete models under healthy and faulty conditions are developed by using the Tustin transformation for digital implementation. Moreover, the stator and rotor mutual inductances are derived as a function of the rotor position according to the turn and winding functions distribution. Simulations and experiments are performed on a 2.2-kW/380-V/50-Hz three-phase and four-pole induction motor to show the performance of the stator and rotor faults, where the saturation effect is considered in simulations by exploiting the measurements of a no load test. The simulation results are in close agreement with the experimental results. Furthermore, magnitudes of the characteristic frequencies of 2f1 in torque and (1 ± 2s)f1 in current are analyzed to evaluate the stator and rotor fault severity. Both indicate that the stator fault severity is related to the short circuit resistance. Further, the number of shorted turns and the number of continuous broken bars determines the rotor fault severity.

Online Inverter Open-circuit Fault Diagnosis for Fault Tolerant Permanent Magnet Synchronous Motor System under Multi-Fault Condition

A Fault Tolerant Control Strategy for Dual Three-Phase PMSM under Single-Phase Open Circuit Fault Considering Inductance Asymmetry

Fault Tolerant Control of Harmonic Injected Nine-Phase Flux Switching Permanent Magnet Motor Drive System

Modeling and Evaluation of Stator and Rotor Faults for Induction Motors

A Novel Diagnostic Method for Single and Dual Power Switch Open-Circuit Faults of Six-Phase FTPMSM System even in Fault Tolerant Operation

Fault-Tolerant Control of Dual Three-Phase PMSM Based on Minimum Copper Loss under Multi-Phase Open and Open-Switch Faults

Single- and Two-Phase Open-Circuit Fault Tolerant Control for Dual Three-Phase PM Motor Without Phase Shifting

Open-Circuit Fault-Tolerant Control of a Six-Phase Asymmetric Permanent Magnet Synchronous Motor Drive System

Control of Dual Three-Phase Permanent Magnet Synchronous Motor under Open Phase Fault Conditions

Fault-Tolerant Control of Dual-Three-Phase PMSM under Open-Phase Fault Based on Two-Individual Current Control

Harmonic Model and Remedy Strategy of Multiphase PM Motor under Open-Circuit Fault

Fault Tolerant Control of a Multiphase Motor with Non-Sinusoidal Source under Open-Phase Conditions

Adaptive Torque Ripple Suppression Methods of Three-Phase PMSM During Single-Phase Open-Circuit Fault-Tolerant Operation

Fault Tolerant Inverter Based Direct Torque Control for Permanent Magnet Synchronous Motor

Diagnosis and Tolerance of Common Electrical Faults in T-Type Three-Level Inverters Fed Dual Three-Phase PMSM Drives

Research on Fault Tolerant Inverter Based Permanent Magnet Synchronous Motor Direct Torque Control Drives

Optimized Fault-Tolerant Control of Dual Three-Phase PMSM Under Open-Switch Faults

Open-fault diagnosis and tolerant control of a dual inverter fed open-end winding interior permanent magnet synchronous motor

An Embedded Fault-Tolerant Control Method for Single Open-Switch Faults in Standard PMSM Drives

Inter-turn Fault Detection for the Inverter-Fed Induction Motor Based on the Teager-Kaiser Energy Operation of Switching Voltage Harmonics

Study on Inverter Fault-Tolerant Operation of PMSM DTC