Abstract:Excellent thermoelectric cooling and power generation are simultaneously realized in an n-type PbTe-based thermoelectric material. The cooling temperature difference (Delta T) of approximate to 15.6 K, maximum power density of approximate to 0.4 W cm(-2) and conversion efficiency of approximate to 1.5% with T-C = 295 K and T-H = 765 K can be obtained in a single-leg device composed of PbTe-30%SnSe-1.5%Cu. This advanced thermoelectric performance in n-type PbTe-30%SnSe-1.5%Cu mainly originates from its high-ranged ZT value achieved through optimizing its bandgap, carrier density, and microstructure. The bandgap in PbTe is first reduced by SnSe alloying to facilitate the carrier transport properties at low temperature range (300-573 K). With further tuned carrier density, the average power factor increases from approximate to 10.2 mu W cm(-1) K-2 in Pb0.985Sb0.015Te-30%SnSe to approximate to 16.2 mu W cm(-1) K-2 in PbTe-30%SnSe-1.5%Cu at 300-773 K. Moreover, microstructure observation reveals high-density dislocations in PbTe-30% SnSe-1.5% Cu, which can dramatically suppress the room-temperature lattice thermal conductivity from approximate to 2.21 Wm(-1) K-1 in Pb0.985Sb0.015Te to approximate to 0.53 Wm(-1) K-1 in PbTe-30%SnSe-1.5%Cu. As a result, a room-temperature ZT value of approximate to 0.7 and high average ZT value (ZT(ave)) of approximate to 0.98 can be obtained in PbTe-30%SnSe-1.5%Cu at 300-573 K, which makes its performance comparable to the commercial n-type Bi2Te3-based thermoelectric material.

Band Sharpening and Band Alignment Enable High Quality Factor to Enhance Thermoelectric Performance in N-Type PbS.

Enhanced thermoelectric performance of n -type PbTe bulk materials fabricated by semisolid powder processing

High Thermoelectric Efficiency Of N-Type Pbs

Promoting SnTe As an Eco‐Friendly Solution for P‐pbte Thermoelectric Via Band Convergence and Interstitial Defects

High-Ranged <i>ZT</i> Value Promotes Thermoelectric Cooling and Power Generation in n-Type PbTe

High Performance of N-Type (Pbs)(1-X-y)(pbse)(x)(pbte)(y) Thermoelectric Materials

Realizing high-ranged thermoelectric performance in PbSnS2 crystals

Synergistically Optimizing Thermoelectric Transport Properties of N-Type PbTe Via Se and Sn Co-Alloying

Thermopower enhancement in Pb1|[minus]|xMnxTe alloys and its effect on thermoelectric efficiency

Carrier tuning and multiple phonon scattering induced high thermoelectric performance in n-type Sb-doped PbTe alloys

Enhancing Thermoelectric Performance of N-Type PbTe Through Separately Optimizing Phonon and Charge Transport Properties

Synergistically Enhancing Thermoelectric Performance of N‐type PbTe with Indium Doping and Sulfur Alloying

Strained Endotaxial PbS Nanoprecipitates Boosting Ultrahigh Thermoelectric Quality Factor in n-Type PbTe As-Cast Ingots

Achieving Higher Thermoelectric Performance of N-Type PbTe by Adjusting the Band Structure and Enhanced Phonon Scattering

Synergistically optimizing carrier and phonon transport properties in n-type PbTe through I doping and SnSe alloying

Approaching Topological Insulating States Leads to High Thermoelectric Performance in N-Type PbTe

Realization of Valence Band Convergence for High Thermoelectric Performance P-Type PbS

Achieving higher thermoelectric performance of n-type PbTe by adjusting band structure and enhanced phonons scattering

Comprehensive Investigation on the Thermoelectric Properties of P‐type PbTe‐PbSe‐PbS Alloys

Enhancing Thermoelectric Transport Properties of N-Type PbS Through Introducing CaS/SrS

High Performance Thermoelectrics from Earth-Abundant Materials: Enhanced Figure of Merit in Pbs Through Nanostructuring Grain Size