Abstract:Inorganic CsPbIBr2 perovskite has been considered as a promising light-absorbing material for solar cells due to its high stability and suitable bandgap. Although the remarkable improvement of CsPbIBr2 PSC has been achieved, the efficiency of this cell is still lower than those of other analogues and far below its theoretical limit. This is mainly due to the serious charge recombination in the as-fabricated CsPbIBr2 cells derived from the poor-quality CsPbIBr2 perovskite film with a large quantity of defects and numerous grain boundaries. Therefore, fabricating high-quality CsPbIBr2 perovskite film is a key factor for the further efficiency improvement of CsPbIBr2 PSCs. Herein, phenylthiourea (PTU) additive is introduced into the CsPbIBr2 precursor to tailor the crystallization of CsPbIBr2 perovskite for fabricating high-quality CsPbIBr2 perovskite. The C=S group of PTU can coordinate with PbBr2 in the precursor owing to the lone-pair electrons on S and the empty orbits of Pb2+. The strong interaction between PTU and the CsPbIBr2 precursor components can form PTU·Pb···Br(I) intermediate phase in the precursor upon PTU introduction. The PTU·Pb···Br(I) intermediate phase can reduce the nucleation rate of perovskite and modulate the perovskite crystal growth because the extra energy is required to break the strong coordination bond in the intermediate phase, resulting in a low crystallization rate of CsPbIBr2 perovskite. Such a retardation of perovskite crystallization is conducive to the formation of high-crystallinity perovskite film with smooth surface, large crystal grains, high crystallization, and low density of defect. Meanwhile, the decomposition of PTU during thermal annealing makes the S2– inserted into interstitial of CsPbIBr2 crystal lattice, which greatly enhance the stability of CsPbIBr2 perovskite. The carbon-based PSCs with a normal n-i-p structure of FTO/compact-TiO2 layer/meso-TiO2 layer/perovskite film/carbon layer are fabricated, and their photovoltaic performances are measured under a simulated AM1.5 illumination (100 mW·cm–2). The PSC based on PTU-CsPbIBr2 perovskite delivers a high power conversion efficiency of 10.09%, which is much higher than that of the control device. This great improvement of photovoltaic performance can be attributed to the largely promoted perovskite quality, which enhances the charge collection and suppresses the charge recombination in the device. In addition, the unencapsulated device preserves 82% of the initial efficiency after being stored under ambient condition for 35 days, suggesting excellent stability. Therefore, this work provides an effective complementary strategy for effectively improving the performance of inorganic PSCs.

Recycling of FTO/TiO2 Substrates: Route Toward Simultaneously High-Performance and Cost-Efficient Carbon-Based, All-Inorganic CsPbIBr2 Solar Cells.

A Facile Interface Engineering Method to Improve the Performance of FTO/ZnO/CsPbI 3− X Br X ( X < 1)/C Solar Cells

Significant efficiency enhancement of carbon-based CsPbI2Br perovskite solar cells enabled by optimizing tin oxide electron transport layer

Optimizing the Substrate Pre-Heating and Post-Annealing Temperatures for Fabricating High-Performance Carbon-Based CsPbIBr2 Inorganic Perovskite Solar Cells

Enhanced efficiency and long-term stability of all inorganic CsPbBr3 perovskite solar cells via regulation of charge separation and extraction by band engineered-Co3O4 nanocrystals as a hole transport material layer

Enhanced efficiency and long-term stability of all inorganic CsPbBr 3 perovskite solar cells via regulation of charge separation and extraction by band engineered-Co 3 O 4 nanocrystals as a hole transport material layer

Bifunctional Passivation for Efficient and Stable Low-Temperature Processed All-Inorganic CsPbIBr2 Perovskite Solar Cells

Low-temperature Preparation of Titanium Dioxide Thin Layer for Highly Efficient CsPbI3 Perovskite Solar Cells

Charge-Transporting-Layer-Free, Vacuum-Free, All-Inorganic Cspbibr(2)Perovskite Solar Cells Via Dipoles-Adjusted Interface

Charge-Transporting-Layer-Free, Vacuum-Free, All-Inorganic CsPbIBr<sub>2</sub>Perovskite Solar Cells Via Dipoles-Adjusted Interface

Low-temperature preparation of titanium dioxide thin layer for highly efficient CsPbI 3 perovskite solar cells

High-performance carbon-based CsPbI2Br perovskite solar cells via small molecule modification

High-Efficiency (>14%) and Air-Stable Carbon-Based, All-Inorganic CsPbI2Br Perovskite Solar Cells Through a Top-Seeded Growth Strategy

Tailoring of CsPbIBr2 Perovskite Crystallization Via Phenylthiourea for Stable and Efficiency Perovskite Solar Cells

High-Efficiency All-Inorganic Perovskite Solar Cells Tailored by Scalable Rutile TiO 2 Nanorod Arrays with Excellent Stability

Improving the stability and scalability of all-inorganic inverted CsPbI2Br perovskite solar cell

Stable and highly efficient all-inorganic CsPbBr3 perovskite solar cells by interface engineering with NiO NCs modification

Efficient Carbon-Based CsPbBr3 Inorganic Perovskite Solar Cells by Using Cu-Phthalocyanine as Hole Transport Material

Composition and Energy Band–Modified Commercial FTO Substrate for in Situ Formed Highly Efficient Electron Transport Layer in Planar Perovskite Solar Cells

A Solution-Processed Dopant-Free Tin Phthalocyanine (snpc) Hole Transport Layer for Efficient and Stable Carbon-Based CsPbI2Br Planar Perovskite Solar Cells Prepared by a Low-Temperature Process

Water-Based Recycling Process of FTO/SnO2 Substrate for Sustainable Perovskite Solar Cell Technology