Abstract:Poor utilization of ceramic polishing slag and uneven foaming at high temperatures are some of the crucial problems associated with the formation of porous ceramics. To overcome this, the present study was designed to prepare closed-ended polishing slag porous ceramics by controlling the holding time. Scanning electron microscope, XRD, and X-CT were used to investigate the effects of holding time on the microstructure, pore structure, and phase composition of porous ceramics. The results showed that the holding time had a great influence on the physical properties of the samples, and it provides uniform porosity without significant change in the composition of the material phase of the porous ceramics. Under a holding time of 30 min, volume density reached up to 0.68 g/cm 3 , while the water absorption and the apparent porosity were 27.33% and 15.49%, respectively. The compressive strength reached 13.07 MPa, and the pore size distribution is mainly between 25 μm and 100 μm, of which the d30 pore diameter accounted for about 28%, the d50 pore diameter accounted for 25%, the d70 pore diameter accounted for 12%, and the d90 pore diameter accounted for 10% of the pore size distribution. In conclusion, the present study clearly shows that the pore structure and properties of porous ceramics can be effectively controlled by controlling the holding time while using a high volume of polishing slag. The feasibility of X-CT for studying the pore distribution inside porous ceramics was verified.

Preparation Of Ysz Porous Ceramics With Precise Porosity Control

Preparation of Porous YSZ Ceramics by Ball Milling Foaming-Freeze Drying Process

Improved Mechanical Properties of 3YSZ Ceramics Prepared by Pressure-less Sintering Assisted by Cold Sintering under Mild Conditions

Influence of Solid Loading in the Gel-Casting Process on the Microstructure and Properties of Porous YSZ Ceramics

Preparation of unidirectional porous yttria stabilized zirconia ceramics by an alginate self assemble method

Porous yttria-stabilized zirconia ceramics with low thermal conductivity via a novel foam-gelcasting method

High-strength porous YSZ ceramics fabricated by TBA-based gelcasting with high solid loading slurry

Strength Analysis of Porous YSZ&nbsp;Ceramics With the Same Porosity and Different Pore Structure

Effects of mono-dispersed PMMA micro-balls as pore-forming agent on the properties of porous YSZ ceramics

Fabrication and Properties of Porous Yttria-Stabilized Zirconia Ceramics

The microstructural characterization and mechanical response of YSZ ceramic foams fabricated via volume-controlled foaming

Porous Yttria‐stabilized Zirconia Ceramics Fabricated by Nonaqueous‐Based Gelcasting Process with PMMA Microsphere As Pore‐Forming Agent

Microstructure and permeability of porous YSZ ceramics with aligned and gradient pore channels fabricated by freeze casting

Porous Ysz Ceramics Reinforced By Different Kinds Of Fibers

A Novel Way to Fabricate Highly Porous Fibrous YSZ Ceramics with Improved Thermal and Mechanical Properties

Effects of Pore-Forming Agent Content on the Properties of Porous 8ysz Ceramics by Tba Based Gel-Casting

Preparation and Characterization of YSZ Abradable Sealing Coating Through Mixed Solution Precursor Plasma Spraying

Porous Ysz Ceramics with Unidirectionally Aligned Pore Channel Structure: Lowering Thermal Conductivity by Silica Aerogels Impregnation

Effect of holding time on the properties of porous ceramics with high-volume polished slag and its pore structure characteristics

Preparation of Porous YB4 Ceramics Using a Combination of In-Situ Borothermal Reaction and High Temperature Partial Sintering

Control of pore channel size during freeze casting of porous YSZ ceramics with unidirectionally aligned channels using different freezing temperatures