Abstract:The Cu-Cr-Zr copper alloy is known for its outstanding electrical conductivity and fatigue strength. However, the corrosion behaviour of the copper alloy should also be taken into account when adopting it in industrial applications, especially in the marine environments. This research aims to fabricate Cu alloy coupons using the Laser Powder Bed Fusion (LPBF) technique and subsequently test their corrosive performance in simulated seawater. This research confirms that the Cu5Zr precipitate formation during the LPBF process and the Cu2O passive layer formation were the main reason for the enhanced corrosive behavior of the LPBFed copper alloy. The OM (Optical Microscope), FESEM (Field Emission Scanning Electron Microscope) images supported in evaluating melt pool formations and irregularities, and also confirmed the polycrystalline structure. The diffraction pattern from the TEM (Transmission Electron Microscope) analysis confirmed the formation of Cu5Zr precipitate and grain size distribution, while their orientations were obtained from the EBSD (Electron Based Scattered Diffraction) EBSD analysis. Micro hardness was executed on the scanning and building directions, and it was found that the building direction possessed higher hardness of 54 HV0.3 which was 5% higher than in the scanning direction. This significant fluctuation in the hardness value is due to the closely packed equiaxed and columnar grains along the outer and inner regions of the melt pools. Potentio-dynamic polarization (PD) and electrochemical impedance spectroscopy (EIS) tests were performed on the printed copper alloy parts for various immersion periods of 0, 9, 18 and 38 hours. Further, the XRD (X-ray Diffraction) analysis was performed on the corroded surface and it confirmed the Cu2O passive layer and the occurrence of Cu5Zr precipitate. The occurrence of Cu5Zr precipitates and Cu2O passive layer formation helped attain the maximum polarization resistance of 2033.8 ohm and minimum current density of 5.928x10-6 A/cm2 with minimum surface roughness of 3.447μm.

Microstructures and Corrosion Resistance of Zircaloy-4 after Surface Alloying with Copper by High-Current Pulsed Electron Beam

Effect of Nb and Cu on α/β Phase Transition Temperature and Corrosion Behavior of New Type Zirconium Alloys

Surface Modifications of a Hyperperitectic Zn-10 Wt% Cu Alloy by Pulsed Electron Beam Treatment

Surface Modification of Aluminized Cu-10fe Alloy by High Current Pulsed Electron Beam

Microstructure and Properties of Mechanical Alloying Al-Zr Coating by High Current Pulsed Electron Beam Irradiation

Effect of the High Current Pulsed Electron Beam Treatment on the Surface Microstructure and Corrosion Resistance of a Mg-4Sm Alloy

Microstructure and property modifications in surface layers of a Mg-4Sm-2Al-0.5Mn alloy induced by pulsed electron beam treatments

Surface Microstructure Modifications and In-Vitro Corrosion Resistance Improvement of a WE43 Mg Alloy Treated by Pulsed Electron Beams

Effect of High Current Pulsed Electron Beam Treatment on Surface Microstructure and Wear and Corrosion Resistance of an AZ91HP Magnesium Alloy

Surface Modifications of a Cold Rolled 2024 Al Alloy by High Current Pulsed Electron Beams

Microstructure and Liquid Phase Separation of Cucr Alloys Treated by High Current Pulsed Electron Beam

Microstructure modifications and corrosion behaviors of Cr4Mo4V steel treated by high current pulsed electron beam

Effect of Laser Surface Treatment on the Corrosion Resistance of Zircaloy-4 at High Temperature

Characterization of surface coarse-grained structure and improved corrosion resistance for Zr-4 alloy at high temperature

Surface microstructure and property modifications in a Mg-8Gd-3Y-0.5Zr magnesium alloy treated by high current pulsed electron beam

Effect of Copper Ions Implantation on Corrosion Behavior of Zircaloy-4 in 1 M H2so4

Consequence of coherent Cu 5 Zr precipitates and Cu 2 O passive layer formation on the corrosive behaviour of additively processed Cu-Cr-Zr alloy in simulated seawater

Surface Modification of Cu–25Cr Alloy Induced by High Current Pulsed Electron Beam

Evolution of Surface Microstructure of Cu-50Cr Alloy Treated by High Current Pulsed Electron Beam

Mechanical, Wetting and Corrosion Properties of a Zr-based Amorphous Alloy Composite Consolidated by Spark Plasma Sintering

Surface Modification of Cucr25 Alloy with Cr Coatings Treated by High Current Pulsed Electron Beam