Abstract:The interest of additive manufacturing (AM) Al-base alloys for lightweight applications, especially the novel scandium modified Al-Mg alloy is growing. In this work, the selective laser melting (SLM) of Al-6.2Mg-0.36Sc-0.09Zr alloy was systematically investigated, with a particular emphasis on densification, microstructure and properties. An increased laser energy density leads to a higher densification level and a better the surface finish of the SLM samples. The surface exhibits a large number of oxides at the scan track interface and microcracks owing to the high Mg content. The x-ray diffraction reveals a (200) texture due to the preferential solidification in the 〈100〉 direction and the diffraction peaks shift to a higher angle after the laser melting owing to the Mg loss. The horizontal plane presents equiaxed grains while the vertical plane presents columnar ones with the aggregation of 〈001〉 orientation. The microstructure exhibits alternately coarse and fine grain that beneath the weld pool is a fine grained band while the central zone of weld pool shows coarse columnar grains epitaxial above the fine grain band, which is caused by the segregation of Al3(Sc,Zr) particles in weld pool boundary. The microhardness of the densest part is directionally independent, which is much higher than cast alloy but lower than homogenizing annealed alloy. The maximal compression strength of SLM Al-Mg-Sc-Zr alloy reaches 390.25MPa. The electrochemical corrosion property of SLM alloy is higher than cast one. Better understanding of the metallurgical mechanisms during SLM of the present alloy will help pave the way for designing SLM suitable Al-base alloys.

Effect of bimodal microstructure on the tensile properties of selective laser melt Al-Mg-Sc-Zr alloy

Effect of laser power on microstructures and properties of Al-4.82Mg-0.75Sc-0.49Mn-0.28Zr alloy fabricated by selective laser melting

Effect of Al3(Sc, Zr) and Mg2Si Precipitates on Microstructure and Tensile Properties of Selective Laser Melted Al-14.1Mg-0.47Si-0.31Sc-0.17Zr Alloy

Tensile property and microstructure of Al−4.77Mn−1.37Mg−0.67Sc−0.25Zr alloy under different selective laser melting processing parameters

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Microstructure and Mechanical Properties of Selective Laser Melted Al–2.51Mn–2.71Mg–0.55Sc–0.29Cu–0.31Zn Alloy Designed by Supersaturated Solid Solution

Selective laser melting of Al-3.48Cu-2.03Si-0.48Sc-0.28Zr alloy: Microstructure evolution, properties and metallurgical defects

Selective Laser Melting of High Strength Al–Cu–Mg Alloys: Processing, Microstructure and Mechanical Properties

Microstructure and mechanical properties of Al-Fe-Sc-Zr alloy additively manufactured by selective laser melting

Densification, microstructure and properties of Sc and Zr modified Al-Mn alloy prepared by selective laser melting

Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

Microstructure, Mechanical Properties and Strengthening Mechanisms of AlCu5MnCdVA Aluminum Alloy Fabricated by Selective Laser Melting

Selective Laser Melting of Al-Cu-Mn-Mg Alloys: Processing and Mechanical Properties

Densification, Microstructure and Mechanical Properties of an Al-14.1Mg-0.47Si-0.31Sc-0.17Zr Alloy Printed by Selective Laser Melting

Microstructure, metallurgical defects and hardness of Al–Cu–Mg–Li–Zr alloy additively manufactured by selective laser melting

Microstructures and Mechanical Property of AlMgScZrMn - A Comparison Between Selective Laser Melting, Spark Plasma Sintering and Cast

Evolution of Heterogeneous Microstructure and its Effects on Tensile Properties of Selective Laser Melted AlSi10Mg Alloy

Selective Laser Melting of A Novel Sc and Zr Modified Al-6.2 Mg Alloy: Processing, Microstructure, and Properties

Effect of Zr Content on Formability, Microstructure and Mechanical Properties of Selective Laser Melted Zr Modified Al-4.24Cu-1.97Mg-0.56Mn Alloys

Developing a high-strength Al-Mg-Si-Sc-Zr alloy for selective laser melting: Crack-inhibiting and multiple strengthening mechanisms

Cracking Behavior, Microstructure and Properties of Selective Laser Melted Al-Mn-Mg-Sc-Zr Alloy