Non-thermal plasma degradation of tar in gasification syngas

Fanrui Meng,Xianchun Li,Hanzhao Liang,Guanyu Wang,Liming Lu,Jianguo Liu

DOI: https://doi.org/10.1016/j.cep.2019.107656

IF: 4.264

2019-01-01

Chemical Engineering and Processing - Process Intensification

Abstract:The degradation pathway of toluene molecular

What problem does this paper attempt to address?

Advance in the treatment methods of biomass tar

Lehao LI,Guangdong WEN,Qiwei YANG,Ming ZHANG,Huabin XING,Baogen SU,Qilong REN

DOI: https://doi.org/10.16085/j.issn.1000-6613.2016-2292

2017-01-01

Abstract:Biomass gasification is a common technology of converting biomass into energy.The tar produced in the process ofbiomass gasification not only leads to equipment corrosion,pipeline blockage and secondary pollution,but also reduces the efficiency of biomass gasification.The classification,potential hazard and treatment methods of biomass tar are reviewed in this paper,with a focus on the recent research progress of catalytic cracking and plasma treatment methods.The advantages and disadvantages of different methods were compared.Physical method has the advantages of simple devices and easy operation,but the energy is not fully utilized and the secondary pollution exists.Thermal cracking can convert tar into gas and increase the energy of the produced gas,however,the process needs high temperature and cost.Having the lower temperature than thermal cracking,the catalytic cracking is the most active field in tar treatment,but the catalysts have the disadvantages of poor stability,easy deactivation,high cost etc.Plasma methods include cold plasma method and thermal plasma method,which are newly developed treatment methods of biomass tar in recent years.Possessing the characteristics of high temperature,high enthalpy and high electron density,the thermal plasma method provides new opportunity for the development of biomass tar processing technology.
VOCs degradation with non-thermal plasma and Ag-MnOx catalysis

Xiujuan Tang,Meng Wang,Weiqiang Feng,Fada Feng,Keping Yan

2011-01-01

Abstract:Non-thermal plasma (NTP) is effective for degradation of aromatic molecules, achieving complete mineralization, however, is difficult. In contrast, thermal catalysis may be very effective toward achieving complete mineralization at high temperatures. Its drawbacks at a low processing temperature are undesirable intermediate byproducts production. By integrating dielectric barrier discharge with home-made Ag-MnOx catalyst, we have succeeded in achieving both VOCs complete decomposition and without toxic byproducts production. As an example, this paper reports toluene decomposition in air. The effects of the reaction temperature and the plasma specific energy density on the decomposition efficiency and byproducts formation are experimentally investigated. Very effective synergetic effect between the NTP and catalyst has been observed for VOCs decomposition.
Plasma-Catalytical Removal of Tars from Fuel Gas Obtained by Biomass Gasification

Gnus A. J. M. Pemen,Lopamudra Devi,Keping Yan,Bert E. J. M. van Heesch,Ruud Kerst,Krisztof. J. Ptasinski,Sreejit A. Nair

2007-01-01

Journal of Advanced Oxidation Technologies

Abstract:In view of the worldwide concern about the depletion of fossil fuels and environmental problems associated with these sources, biomass is getting increased attention as a source of renewable energy and chemicals. Biomass gasification has a significant higher biomass to power efficiency than biomass combustion. However, gasification of biomass also produces significant amounts of heavy hydrocarbons (referred to as "tars") along with particulates. These tars will condense in downstream equipment, or deposit on active sites of catalysts, leading to loss of activity and the need for frequent regeneration. Hence it is necessary to remove the tars. Here we discuss the use of pulsed corona and plasma-catalysis as alternative methods for catalytic and thermal treatment. In both catalytic as well as thermal treatment processes, the fundamental mechanism involves creation and stabilizing of reactive species, which thereafter initiate the necessary reactions under kinetic and thermodynamic limitations. The same can be expected to occur in a non-thermal plasma, where similar species can be created by energetic electron-molecule collisions.
Tar Removal from Biomass-Derived Fuel Gas by Pulsed Corona Discharges

A. J. M. Pemen,S. A. Nair,K. Yan,E. J. M. van Heesch,K. J. Ptasinski,A. A. H. Drinkenburg

DOI: https://doi.org/10.1016/s0378-3820(03)00053-5

IF: 8.129

2003-01-01

Fuel Processing Technology

Abstract:To supply combustion engines or gasturbines with fuel gas obtained from biomass gasification, it is necessary to clean the fuel gas. Also the production of chemicals by processes such as Fisher-Tropsch requires a high gas quality. Especially heavy aromatic hydrocarbons (“tars”) must be removed. In this work, we give an overview of our investigations on tar removal by pulsed corona discharges as an alternative approach to catalytic or thermal tar cracking. Experimental results (at a gas temperature of 200°C) are reported for the removal of various model tar components in synthetic fuel gas. In order to identify the major reaction pathways, experiments were also done on tars in individual fuel gas components. The results show that tar removal by pulsed corona processing is possible. The process for tar removal is mainly via oxidation. Also termination reactions by CO play an important role.
Steam reforming of toluene as biomass tar model compound in a gliding arc discharge reactor

Shiyun Liu,Danhua Mei,Li Wang,Xin Tu

DOI: https://doi.org/10.1016/j.cej.2016.08.005

IF: 15.1

2017-01-01

Chemical Engineering Journal

Abstract:Non-thermal plasma is considered a promising and attractive approach for the removal of tars from biomass gasification to deliver a clean and high quality syngas (a mixture of H2 and CO). In this study, an AC gliding arc discharge (GAD) reactor has been developed for the conversion of toluene as a tar model compound using nitrogen as a carrier gas. The presence of steam in the plasma reaction produces OH radicals which open a new reaction route for the conversion of toluene through a stepwise oxidation of toluene and intermediates, resulting in a significant enhancement in both the conversion of toluene and the energy efficiency of the plasma process. The effects of steam-to-carbon (S/C) molar ratio, toluene feed rate and specific energy input (SEI) on the performance of the plasma steam reforming of toluene have been investigated. The optimal S/C molar ratio was found to be between 2 and 3 for high toluene conversion and energy efficiency. The maximum toluene conversion of 51.8% was achieved at an optimal S/C molar ratio of 2, a toluene feed flow rate of 4.8ml/h and a SEI of 0.3kWh/m3, while the energy efficiency of the plasma process reached a maximum (∼46.3g/kWh) at a toluene feed flow rate of 9.6ml/h and a SEI of 0.19kWh/m3. H2, CO and C2H2 were identified as the major gas products with a maximum syngas yield of 73.9% (34.9% for H2 and 39% for CO). Optical emission spectroscopy (OES) has been used to understand the role of steam on the formation of reactive species in the plasma conversion of toluene. The possible reaction pathways in the plasma conversion of toluene have also been proposed by combined means of the analysis of gas and liquid samples and OES diagnostics.
Removal of toluene as a biomass tar surrogate by combining catalysis with nonthermal plasma: understanding the processing stability of plasma catalysis

Bin Xu,Nantao Wang,Jianjun Xie,Yanpei Song,Yanqin Huang,Wenshen Yang,Xiuli Yin,Chuangzhi Wu

DOI: https://doi.org/10.1039/d0cy01211d

2020-01-01

Abstract:The processing stability of plasma catalysis was understood in terms of tar removal.

chemistry, physical
Mechanisms of Toluene Removal in Relation to the Main Components of Biosyngas in a Catalytic Nonthermal Plasma Process

Bin Xu,Jianjun Xie,Xiuli Yin,Hao Liu,Chenggong Sun,Chuangzhi Wu

DOI: https://doi.org/10.1021/acs.energyfuels.9b00273

IF: 4.6541

2019-01-01

Energy & Fuels

Abstract:In this study, a packed-bed dielectric barrier discharge reactor was built for the removal of biomass gasification tar. Two kinds of packing materials, glass pellets and a Ni/gamma-Al2O3 catalyst, were employed for the plasma-alone process and the plasma catalytic process, respectively. Toluene was used as the tar surrogate, and five typical gas combinations, N-2, N-2 + CO2, N-2 + CO2 + CO, N-2 + CO + H-2, and simulated gasification gas (SGG), were selected as carrier gases. The effects of the main components of the gasification gas on toluene removal under plasma and/or catalysis treatment were studied. The results indicated that the highest removal efficiency in the plasma-alone process was achieved in the N-2 atmosphere, and the addition of H-2, CO, or CO2 to N-2 led to a decrease in the removal performance. When Ni/gamma-Al2O3 was introduced into the plasma process, the best removal efficiency was obtained in the N-2 + CO2 atmosphere. However, the positive effect of CO2 on toluene removal switched to a negative effect when CO2 coexists with CO and H-2 in the gas mixture. In addition, both the terminating effect at low temperature and the occurrence of methanation induced by CO at high temperature could significantly inhibit the removal of toluene in the plasma catalytic process. Typically, in the SGG atmosphere, the highest toluene removal efficiencies under plasma-alone, catalysis-alone, and plasma catalysis treatments were 33.5, 38.6, and 92.5%, respectively. Furthermore, no CN-containing or O-containing compounds were identified as the major by-products in the plasma catalytic process, which is significantly different from what was observed in the plasma-alone process. Moreover, a detailed mechanism of toluene removal under plasma and plasma catalysis treatment was proposed after the analysis of gas and liquid products.
The Thermal Treatment Properties of the Tars from Sewage Sludge Gasification

Wu Xia,Xie Liping,Li Tao

DOI: https://doi.org/10.4028/www.scientific.net/amr.113-116.1158

2010-01-01

Advanced Materials Research

Abstract:The properties of pyrolysis and combustion of five tars, which are produced from the gasification of five sewage sludges in the external heated downdraft reactor under the gasification temperature of 800 °C and the air flow rate of 0.05 m3/h, were studied by thermal gravimetric analysis with a heating rate of 10 °C/min in the atmosphere of nitrogen and air, respectively. The results indicate that the thermal processes of five tars in the two atmospheres can be divided into two stages. The releasing of light organic matters happens in the first stage, and there also exists the decomposition reaction during pyrolysis. The second stage is the decomposition or combustion stage of the remaining heavy organic matters for the pyrolysis or combustion. The reaction mechanisms in the two atmospheres have been studied with Coats-Redfern equation. It shows that the mechanisms of five tars in the same atmosphere are different.
Decomposition of naphthalene as tar model compound from the gasification of municipal solid waste by rotating gliding arc plasma

Xin YAN,Xiaodong LI,Fengsen ZHU,Xiangzhi KONG,Jianhua YAN

DOI: https://doi.org/10.16085/j.issn.1000-6613.2017-1134

2018-01-01

Abstract:In this study,a novel rotating gliding arc(RGA)plasma co-driven by a magnetic field and a tangential gas flow was used for tar decomposition. Naphthalene in nitrogen flow was proposed as a tar surrogate. The effects of injection concentration,gas flow rate and preheating temperature on naphthalene degradation efficiency and gas production were investigated. In addition,liquid byproducts were characterized by gas chromatography-mass spectrometry(GC/MS). With the rise of the injection concentration,the degradation efficiency of naphthalene increased first,reaching a maximum value of 88.3% at 6mg/L,and then decreased. With the rise of gas flow rate from 2L/min to 12L/min,the degradation efficiency of naphthalene decreased continuously from 92.1% to 82.5%. Increasing the preheating temperature could promote the degradation of naphthalene. The results showed that the main gas products were H2and C2H2,with maximum selectivity of 44.0% and 13.7% respectively. The variation trend of the selectivity of H2and C2H2were consistent with that of naphthalene degradation efficiency. The major liquid byproducts were acetylene,indene and acenaphthylene,whose GC/MS peak areas were 2—3 orders of magnitude lower than that of naphthalene. On this basis,the reaction pathways and mechanisms of naphthalene decomposition in the plasma zone were preliminary proposed and discussed.
Steam Reforming of Toluene and Naphthalene As Tar Surrogate in a Gliding Arc Discharge Reactor.

Hao Zhang,Fengsen Zhu,Xiaodong Li,Ruiyang Xu,Li,Jianhua Yan,Xin Tu

DOI: https://doi.org/10.1016/j.jhazmat.2019.01.085

IF: 13.6

2019-01-01

Journal of Hazardous Materials

Abstract:Steam reforming of mixed toluene and naphthalene as tar surrogate has been investigated in an AC gliding arc discharge plasma, with particular emphasis on better understanding the effect of steam and CO2 on the reaction performance. Results show that H2, C2H2 and CO are the major gas products in the plasma steam reforming of tar for energy recovery. The addition of a small amount of steam remarkably enhances the conversions of both toluene and naphthalene, from 60.4% to 76.1% and 57.6% to 67.4%, respectively, as OH radicals formed by water dissociation create more reaction pathways for the conversion of toluene, naphthalene and their fragments. However, introducing CO2 to this process has a negative effect on the tar reforming. Optical emission spectroscopic diagnostics has shown the formation of a variety of reactive species in the plasma process. Trace amounts of monocyclic and bicyclic aromatic condensable by-products are also detected. The destruction of toluene and naphthalene can be initiated through the collisions of tar surrogates with energetic electrons, N2 excited species, OH and O radicals etc. Further optimization of the plasma tar destruction is still needed because the complexity of the tar component in a practical gasifier could decrease the tar conversions.
Destruction of Toluene, Naphthalene and Phenanthrene As Model Tar Compounds in a Modified Rotating Gliding Arc Discharge Reactor

Xiangzhi Kong,Hao Zhang,Xiaodong Li,Ruiyang Xu,Ishrat Mubeen,Li,Jianhua Yan

DOI: https://doi.org/10.3390/catal9010019

IF: 3.9

2018-01-01

Catalysts

Abstract:Tar removal is one of the greatest technical challenges of commercial gasification technologies. To find an efficient way to destroy tar with plasma, a rotating gliding arc (RGA) discharge reactor equipped with a fan-shaped swirling generator was used for model tar destruction in this study. The solution of toluene, naphthalene and phenanthrene is used as a tar surrogate and is destroyed in humid nitrogen. The influence of tar, CO2 and moisture concentrations, and the discharge current on the destruction efficiency is emphasized. In addition, the combination of Ni/γ-Al2O3 catalyst with plasma was tested for plasma catalytic tar destruction. The toluene, naphthalene and phenanthrene destruction efficiency reached up to 95.2%, 88.9%, and 83.9% respectively, with a content of 12 g/Nm3 tar, 12% moisture, 15% CO2, and a flow rate of 6 NL/min, whereas 9.3 g/kW·h energy efficiency was achieved. The increase of discharge current is advantageous in terms of decreasing black carbon production. The participation of Ni/γ-Al2O3 catalyst shows considerable improvement in destruction efficiency, especially at a relatively high flow rate (over 9 NL/min). The major liquid by-products are phenylethyne, indene, acenaphthylene and fluoranthene. The first two are majorly converted from toluene, acenaphthylene is produced by the co-reaction of toluene and naphthalene in the plasma, and fluoranthene is converted by phenanthrene.
Simultaneous Removal of Toluene, Naphthalene, and Phenol as Tar Surrogates in a Rotating Gliding Arc Discharge Reactor

Ruiyang Xu,Fengsen Zhu,Hao Zhang,Petric Marc Ruya,Xiangzhi Kong,Li Li,Xiaodong Li

DOI: https://doi.org/10.1021/acs.energyfuels.9b03529

2020-01-14

Abstract:In this study, a rotating gliding arc (RGA) plasma reactor was investigated for the decomposition of gasification derived tar. Toluene, naphthalene, and phenol were selected as tar surrogates to be simultaneously decomposed. The effects of steam addition, preheating temperature, tar, and CO2 concentration were studied and the decomposition pathways of tar model compounds were proposed. The optimum amount of steam can facilitate tar destruction, enhance H2 yield, and, importantly, suppress the formation of carbon black. The conversions of toluene, naphthalene, and phenol can be up to 85.8, 76.4, and 93.4%, respectively, when 8–12% steam is applied in the system. As expected, the increase of tar or CO2 concentration reduces the conversions of tar. Interestingly, increasing the preheating temperature to 600 °C enhances the tar conversions but is then surprisingly followed by a slight drop with the subsequent increase in temperature. The conversions of the three components decrease in the order of phenol > toluene > naphthalene under the studied conditions. Primary decomposition products of toluene, naphthalene, and phenol are determined to be benzyl, naphthyl, and phenoxy compounds, which would be further degraded by active species such as N2 (A3∑u+), OH radicals, O radicals, etc. into smaller molecules like H2, CO, and CO2.

energy & fuels,engineering, chemical
Enhanced Reforming of Mixed Biomass Tar Model Compounds Using a Hybrid Gliding Arc Plasma Catalytic Process

Danhua Mei,Shiyun Liu,Yaoling Wang,Haiping Yang,Zheng Bo,Xin Tu

DOI: https://doi.org/10.1016/j.cattod.2019.05.046

IF: 5.3

2019-01-01

Catalysis Today

Abstract:Plasma-catalytic steam reforming of mixed tar model compounds (toluene and naphthalene) from biomass gasification has been carried out in a gliding arc discharge (GAD) plasma reactor. The influence of three catalysts (15Ni, 7.5Ni7.5Co and 15Co) on the performance of the plasma reforming of toluene and naphthalene has been evaluated including the conversion, the energy efficiency, the yield/selectivity of gaseous products and the formation of by-products. A plasma-catalysis synergy was generated when introducing the catalysts to the plasma tar reforming process. The highest toluene conversion of 95.7% and naphthalene conversion of 83.4% were achieved when the 7.5Ni7.5Co catalyst was integrated with the GAD plasma at a total tar concentration of 16.0 g/Nm(3) and a discharge power of 75 W. The corresponding energy efficiency for the conversion of toluene and naphthalene was 38.0 g/kWh and 2.3 g/kWh, respectively, giving the highest total tar conversion of 95.1% and overall energy efficiency of 40.3 g/kWh. The coupling of GAD with the 7.5Ni7.5Co catalyst also showed the highest yield of H-2 (42.3%) and CO (37.3%) and the highest CO selectivity of 40.1%. In addition, the combination of the GAD plasma with 7.5Ni7.5Co reduced the carbon deposition on the catalyst surfaces and the formation of by-products in the plasma-catalytic tar reforming process. The enhanced reducibility and NiCo alloy formation of the 7.5Ni7.5Co catalyst contribute to the enhanced conversion of mixed tar compounds and the formation of the plasma-catalysis synergy in the hybrid plasma-catalytic tar reforming process.
Removal of Toluene As a Biomass Tar Surrogate in a Catalytic Nonthermal Plasma Process

Bin Xu,Jianjun Xie,Hao Zhan,Xiuli Yin,Chuangzhi Wu,Hao Liu

DOI: https://doi.org/10.1021/acs.energyfuels.8b02444

IF: 4.6541

2018-01-01

Energy & Fuels

Abstract:In this study, a packed-bed dielectric barrier discharge (DBD) reactor was developed to investigate the removal of biomass tar in a fuel gas atmosphere. Toluene was used as the tar surrogate, and the catalyst used was a Nickel-based catalyst (Ni/gamma-Al2O3) because of its high activity and low cost. In addition, another two kinds of packing materials (glass pellets and gamma-Al2O3 pellets) were employed to make a comparison with the Ni/gamma-Al2O3 catalyst. The research has focused on the removal efficiency of toluene and the effects of carrier gas, reaction temperature, Ni loading, and concentration of toluene. The results indicated that two supplementary packing materials could not realize an effective removal of toluene. On the contrary, Ni/gamma-Al2O3 combined with plasma showed a significant synergetic effect and hence a great toluene removal potential. On one hand, the removal efficiency initially decreased within the temperature range of 200-300 degrees C and then significantly increased within the temperature of 300-400 degrees C during plasma-catalytic process. At the optimal temperature of 400 degrees C, the toluene removal efficiency could reach the maximum values of 80.2%, 91.7%, and 100.0% when the Ni loading was 3, 5, and 10 wt %, respectively. On the other hand, an increase in the inlet toluene concentration slightly reduced removal-efficiency but increased the energy efficiency, reaching the highest value of 16.8 g/kWh. The introduction of plasma enhanced the methanation reaction of the fuel gas occurring in the catalytic process, which was favorable at high temperatures. Based on these findings, the mechanisms and pathways of toluene destruction in the plasma-catalytic process were proposed and elucidated.
Photothermal Steam Reforming: A Novel Method for Tar Elimination in Biomass Gasification

Guanyi Chen,Xiaoshan Dong,Beibei Yan,Jian Li,Kunio Yoshikawa,Liguo Jiao

DOI: https://doi.org/10.1016/j.apenergy.2021.117917

IF: 11.2

2022-01-01

Applied Energy

Abstract:Tar elimination is the bottleneck which hinders the industrial application of gasification due to the risks of corrosion and blockage in downstream components. Tar production decreases the energy efficiency of gasification systems. The steam reforming is attractive for tar treatment, but the high reaction temperature limits its applications. Photothermal catalysis has the potential to decompose organic pollutants, and it is expected to improve tar removal and reduce the reaction temperature. So, the photothermal steam reforming of toluene was performed to evaluate the toluene conversion. The effects of the toluene concentration, the temperature, the steam to carbon ratio, and the ultraviolet light intensity were investigated. The results showed that, compared with the thermal steam reforming, the photothermal steam reforming could significantly improve the conversion of toluene and promote the formation of gaseous products, especially H-2. At 600 degrees C, the conversion of toluene in the photothermal steam reforming was 90.1%, which was 16.3% higher than that in the thermal steam reforming. Moreover, the mechanisms of the photothermal steam reforming were revealed. The introduction of the ultraviolet irradiation could strongly promote the toluene decomposition and alter the reaction pathways. The carbon deposition and agglomeration of the catalyst were inhibited in photothermal steam reforming. Meanwhile, the toluene removal performance and the energy consumption were compared in photothermal and thermal steam reforming. The potential applications of photothermal catalytic tar removal were also described. These findings proposed a novel approach for low-cost but high-efficiency biomass tar removal, thus promoting the clean utilization of biomass energy.
Performance Study on Simultaneous Tar Removal and Bio-Syngas Methanation by Combining Catalysis with Nonthermal Plasma

Bin XU,Jia-qing LI,Jian-jun XIE,Yan-qin HUANG,Xiu-li YIN,Chuang-zhi WU

DOI: https://doi.org/10.1016/s1872-5813(21)60045-2

2021-01-01

Journal of Fuel Chemistry and Technology

Abstract:In this work, simultaneous toluene removal and syngas methanation using the combination of packed-bed dielectric barrier discharge and Ni/γ-Al2O3 catalyst were conducted with the research object of simulated gasification gas (SGG) containing toluene. The effects of reaction temperature, H2/CO ratio and H2O addition on the reaction performances of both toluene removal and SGG methanation were investigated. The results show that high-efficiency simultaneous toluene removal and SGG methanation can be achieved at 400°C under plasma catalysis treatment. When the H2/CO is 3.2, the toluene removal rate and the tar removal rate are close to 100% and 97%, the CO conversion rate and CH4 selectivity approach about 88% and 97%, and the energy efficiencies in toluene removal and SGG methanation processes can reach 9.7 g/(kW·h) and 17.3 mol/(kW·h). Both the high H2/CO ratio and the H2O addition can promote toluene removal and SGG methanation, and reduce the amount of carbon deposition but increase its graphitized degree. Moreover, high H2/CO ratio can rise the heating value of SGG and achieve higher energy efficiencies in both toluene removal and SGG methanation processes, while the H2O addition is difficult to obtain high CH4 selectivity to increase the heating value and is not conducive to the promotion of energy efficiency in SGG methanation process. In addition, for these two simultaneous processes, the SGG methanation process exerts a significant inhibiting effect on toluene removal, but process of toluene removal has less influence on the other process due to the lower concentration of toluene.
Plasma-Assisted Toluene Destruction in Simulated Producer Gas

Fengsen Zhu,Hao Zhang,Jian Yang,Jianhua Yan,Mingjiang Ni,Xiaodong Li

DOI: https://doi.org/10.1246/cl.170547

2017-01-01

Chemistry Letters

Abstract:Toluene is chosen as a model tar compound and destroyed by a rotating gliding arc (RGA) discharge in simulated producer gas. A maximum toluene destruction efficiency of 95.6% is achieved. Meanwhile, the concentration of the useful components of synthesis gas (CO and H-2) is significantly enhanced compared to the initial producer gas, indicating that the RGA plasma has great potential for further and simultaneous application in tar cracking and producer gas upgrading.
Destruction of Toluene by Rotating Gliding Arc Discharge

Fengsen Zhu,Xiaodong Li,Hao Zhang,Jianhua Yan,Mingjiang Ni

DOI: https://doi.org/10.1016/j.fuel.2016.02.065

2016-01-01

Abstract:Summary form only given. Non-thermal plasma is considered as an alternative treatment of tar present in the effluent from gasification processes. In this study, a novel rotating gliding arc (RGA) discharge reactor was developed for tar destruction. Toluene in nitrogen flow is used as a tar surrogate. The physical features of RGA discharge and its application to toluene destruction are investigated at different input concentrations and total gas flow rates. As a result, the highest destruction efficiency could exceed 95%, with a toluene concentration of 10 g/Nm 3 and a total flow rate of 0.24 Nm 3 /h. The two major gaseous products are H 2 and C 2 H 2 , with maximum selectivity of 39.35% and 27.0%, respectively. A higher input concentration slightly reduces this destruction efficiency but the energy efficiency further expanded, with a highest value of 16.61 g of toluene eliminated/kWh. In addition, the liquid and solid byproducts are collected downstream of the RGA reactor and determined qualitatively and semi-quantitatively. The amount and structure of these by-products is instructive for reaching a better comprehension of the chemical consequences of plasma treatment to the model compound and to the carrier gas nitrogen.
In-situ removal of toluene as a biomass tar model compound using NiFe2O4 for application in chemical looping gasification oxygen carrier

Zhen Huang,Anqing Zheng,Zhengbing Deng,Guoqiang Wei,Kun Zhao,Dezhen Chen,Fang He,Zengli Zhao,Haibin Li,Fanxing Li

DOI: https://doi.org/10.1016/j.energy.2019.116360

IF: 9

2020-01-01

Energy

Abstract:Efficient removal of tar is a major challenge for biomass gasification. A scheme based on chemical looping gasification (CLG) provides a promising alternative for converting biomass into syngas with low tar content. The current study investigates the reactivity of NiFe2O4 oxygen carrier for toluene (biomass tar model compound) removal. The NiFe2O4 oxygen carrier shows a dual-function of oxidation-catalysis for toluene cracking and significantly promotes toluene cracked into carbon and H2. A suitable temperature for toluene cracking is determined at 850 °C. As the weight hourly space velocity (WHSV) increases by approximately a factor of nine, the toluene removal decreases slightly by 2.78%. The toluene removal does not significantly decrease with the crystal phase transformation of the oxygen carrier. Addition of steam significantly eliminates the carbon deposition, which decreases to 4.97% at S/C (steam/toluene) ratio of 1.20. The catalytic activity of NiFe2O4 initially remained stable for a long time, and then started showing a slight decrease after transitory activation during the long-term experiment (82 h). These results fully demonstrate that the NiFe2O4 is a good oxygen carrier for tar removal in biomass CLG.

energy & fuels,thermodynamics
Plasma-Catalytic Reforming of Naphthalene and Toluene as Biomass Tar over Honeycomb Catalysts in a Gliding Arc Reactor

Danhua Mei,Shiyun Liu,Jale Yanik,Gartzen Lopez,Martin Olazar,Zhi Fang,Xin Tu

DOI: https://doi.org/10.1021/acssuschemeng.2c02495

2022-07-19

Abstract:Biomass gasification is a promising and sustainable process to produce renewable and CO(2)-neutral syngas (H(2) and CO). However, the contamination of syngas with tar is one of the major challenges to limit the deployment of biomass gasification on a commercial scale. Here, we propose a hybrid plasma-catalytic system for steam reforming of tar compounds over honeycomb-based catalysts in a gliding arc discharge (GAD) reactor. The reaction performances were evaluated using the blank substrate and...

chemistry, multidisciplinary,engineering, chemical,green & sustainable science & technology

Non-thermal plasma degradation of tar in gasification syngas

Advance in the treatment methods of biomass tar

VOCs degradation with non-thermal plasma and Ag-MnOx catalysis

Plasma-Catalytical Removal of Tars from Fuel Gas Obtained by Biomass Gasification

Tar Removal from Biomass-Derived Fuel Gas by Pulsed Corona Discharges

Steam reforming of toluene as biomass tar model compound in a gliding arc discharge reactor

Removal of toluene as a biomass tar surrogate by combining catalysis with nonthermal plasma: understanding the processing stability of plasma catalysis

Mechanisms of Toluene Removal in Relation to the Main Components of Biosyngas in a Catalytic Nonthermal Plasma Process

The Thermal Treatment Properties of the Tars from Sewage Sludge Gasification

Decomposition of naphthalene as tar model compound from the gasification of municipal solid waste by rotating gliding arc plasma

Steam Reforming of Toluene and Naphthalene As Tar Surrogate in a Gliding Arc Discharge Reactor.

Destruction of Toluene, Naphthalene and Phenanthrene As Model Tar Compounds in a Modified Rotating Gliding Arc Discharge Reactor

Simultaneous Removal of Toluene, Naphthalene, and Phenol as Tar Surrogates in a Rotating Gliding Arc Discharge Reactor

Enhanced Reforming of Mixed Biomass Tar Model Compounds Using a Hybrid Gliding Arc Plasma Catalytic Process

Removal of Toluene As a Biomass Tar Surrogate in a Catalytic Nonthermal Plasma Process

Photothermal Steam Reforming: A Novel Method for Tar Elimination in Biomass Gasification

Performance Study on Simultaneous Tar Removal and Bio-Syngas Methanation by Combining Catalysis with Nonthermal Plasma

Plasma-Assisted Toluene Destruction in Simulated Producer Gas

Destruction of Toluene by Rotating Gliding Arc Discharge

In-situ removal of toluene as a biomass tar model compound using NiFe2O4 for application in chemical looping gasification oxygen carrier

Plasma-Catalytic Reforming of Naphthalene and Toluene as Biomass Tar over Honeycomb Catalysts in a Gliding Arc Reactor