Abstract:In this study, the GMAW welding torch was controlled by a stepping motor to achieve a periodic swing. By controlling the swing speed, a micro-variable deposition path was obtained, which was called the micro-control deposition trajectory. The influence of the micro-control deposition trajectory on the arc characteristics, microstructure, and mechanical properties of 304 steel wire arc additive manufacturing was studied. The results showed that the micro-control deposition process was affected by the swing arc and the deposition trajectory and that the arc force was dispersed over the whole deposition layer, which effectively reduced the welding heat input. However, the arc centrifugal force increased with the increase in the swing speed, which easily caused instability of the arc and large spatter. Compared with common thin-walled deposition, the deposition width of micro-control thin-walled deposition components was increased. In addition, the swinging arc had a certain stirring effect on the molten pool, which was conducive to the escape of the molten pool gas and refinement of the microstructure. Below, the interface of the deposition layer, the microstructure of the common thin-walled deposition components, and the micro-control thin-walled deposition components were composed of lathy ferrite and austenite. Compared with the common deposition, when the swing speed increased to 800 °/s, the microstructure consisted of vermicular ferrite and austenite. The tensile strength and elongation of the micro-control thin-walled deposition components are higher than those of the common thin-walled deposition components. The tensile fracture mechanism of the common thin-walled deposition components and the micro-control thin-walled deposition components was the ductile fracture mechanism.

Analysis of arc stability and bead forming with high-speed TW-GIA welding

Analysis of arc interference and welding stability in twin wire GMA welding

Research on a high speed welding technology of triple-wire GMAW

Understanding of the Weld Pool Convection in Twin-Wire GMAW Process

Influence of Interwire Distance and Arc Length on Welding Process and Defect Formation Mechanism in Double-Wire Pulsed Narrow-Gap Gas Metal Arc Welding

Thick-wire swing arc narrow gap GMA welding assisted by pre-embedding cold wires

Influence of Interwire Angle on Undercutting Formation and Arc Behavior in Pulsed Tandem Narrow-Gap GMAW

Multi-objective Optimization of Short-Circuit Gas Metal Arc Welding for Overhang Structures by Grey Relational Analysis Integrated Taguchi Method

Effects of Processing Parameters on Molten Behavior, Arc Stability, and Defect Forming in Swing-Arc Narrow Gap GMA Vertical Up Welding

Experimental Investigation of Integrated Circular Triple-Wire Pulse GMAW of Q960E High-Strength Steel for Construction Machinery

Stability of Double Wires Narrow-gap Gas Metal Arc Welding

Analysis on Weld Quality and Stability by Triple-Electrode High Speed CO2 Welding

Study on Short-Circuiting GMAW Pool Behavior and Microstructure of the Weld with Different Waveform Control Methods

A comparative study on BCTW-GIA and T-DW deposition processes

Arc and Droplet Behaviors in Horizontal Short-Arc Pulsed Gas Metal Arc Welding of 9%ni Steel with ERNiCrMo-3 Welding Wire

Improvement in Microstructure and Properties of 304 Steel Wire Arc Additive Manufacturing by the Micro-Control Deposition Trajectory

Selection of Welding Conditions for Achieving Both a High Efficiency and Low Heat Input for Hot-Wire Gas Metal Arc Welding

An Innovative Methodology in Narrow Gap GTAW for Alternating Magnetic Field with Synchronous Swing of Filler Wire and Arc

A New Method for Refinement of Ti-6Al-4 V Prior-Β Grain Structure in the Alternating Magnetic Field Assisted Narrow Gap Gas Tungsten Arc Welding (AMF-GTAW) Via Filler Wire Oscillation

Investigation of Arc Stability in Wire Arc Additive Manufacturing of 2319 Aluminum Alloy

Effects of Torch Configuration on Arc Interaction Behaviors and Weld Defect Formation Mechanism in Tandem Pulsed GMAW