Abstract:To improve the wear resistance of TC4 titanium alloy, two types of wear-resistant coatings were applied to the surface using laser melting: Ni60 + 50% WC and d22 powder priming. The phase composition and microstructure of the coatings were characterized by X-ray diffractometry (XRD), scanning electron microscopy (SEM), and energy spectroscopy (EDS). The mechanical properties of the coating were tested using an HV-1000 micro-Vickers hardness tester, an HRS-2M high-speed reciprocating friction and wear tester, and a WDW-100D electronic universal testing machine. The results show that Ni60 + 50% WC composite coating and d22 priming + (Ni60 + 50% WC) composite coating mainly consist of W2C, TiC, Ni17W3, Ni3Ti, and TixW1−x phases. Compared to the TC4 substrate, the microhardness of both coatings is significantly higher, approximately 2.8 times the microhardness of the substrate. In frictional wear experiments, the average friction factors of the two coatings and the TC4 substrate are 0.476, 0.55, and 0.865, respectively, and the wear of the two coatings is only 0.0559–0.0769 that of the TC4 substrate, with a significant increase in wear resistance, nearly 17 times higher than that of the substrate. The coating shows flaking, shallow abrasion marks, and granular debris, dominated by adhesive wear and fatigue wear, while the TC4 substrate shows more furrows on the surface, dominated by abrasive wear. The shear bond strengths of the Ni60 + 50% WC composite coating and the d22 powder primed + (Ni60 + 50% WC) composite coating were 188.19 MPa and 49.11 MPa, respectively. Conclusion: both coatings significantly improve the hardness and wear resistance of the TC4 titanium alloy substrate surface, with the Ni60 + 50% WC composite coating performing better in hardness, wear resistance, and bond strength.

MICROSTRUCTURE AND WEAR PROPERTY OF Ti/C MODIFIED LAYERS ON Ti-6Al-4V SUBSTRATE

Effects of Ti Content on Microstructure, Mechanical and Tribological Properties of Ti-doped Amorphous Carbon Multilayer Films

Wear properties of alloyed layers produced by laser surface alloying of pure titanium with B 4 C and T{i} mixed powders

The Wear Behavior of the Laser Cladded Ti-Al-Si Composite Coatings on Ti-6Al-4V Alloy with Additional TiC

Microstructure and tribological properties of laser in-situ synthesized Ti3Al composite coating on Ti-6Al-4V

Microstructure and Wear Resistance of Ti6Al4V Titanium Alloy Laser-Clad Ni60/WC Composite Coating

Development and Characterization of Laser Clad High Temperature Self-Lubricating Wear Resistant Composite Coatings on Ti–6Al–4V Alloy

Influence of Ti on the Microstructure and Performance of Fe-Cr Alloy Cladding Layer

Microstructures and Wear Properties of TiC Coating Produced by Laser Cladding on Ti-6Al-4V with TiC and Carbon Nanotube Mixed Powders

Microstructure and Tribological Properties of NiCrBSi-TiC Laser Clad Layer on Titanium Alloy Substrate

Study Of Wear And Corrosion Resistances Of Ni60-Wc + Tic Composite Coating

Microstructure and tribological behaviors of laser cladded CuAlMnTi–xTiC composite coatings at elevated temperature

Microstructure and properties of Ti–Al–C composite coatings prepared by laser cladding

Microstructure, High-Temperature Wear Resistance, and Corrosion Resistance of Laser Cladded Co-Based Coating

Microstructure and Wear Resistance of Laser Cladding TiC Coat on Titanium Alloy

Microstructural and Performance Analysis of (TiAl)95−xCu5Nix Coatings Prepared via Laser Surface Cladding on Ti–6Al–4V Substrates

Microstructure and wear properties of TiCN/Ti coatings on titanium alloy by laser cladding

Study of the Performance of Laser Melting Wear-Resistant Coatings on TC4 Titanium Alloy Surfaces

Microstructure, mechanical and tribological properties Of A-C/A-C:Ti nanomultilayer film

Microstructure and tribological properties of laser-cladded TiC x /TiAl composite coatings on TC4 alloy

Experimental Study on Friction Characteristics of Micro-Arc Oxidation Modified Layer on Titanium Alloy Surface