Abstract:The Haber–Bosch (HB) process is the primary chemical synthesis technique for industrial production of ammonia (NH3) for manufacturing nitrate-based fertilizer and as a potential hydrogen carrier. The HB process alone is responsible for over 2% of all global energy usage to produce more than 160 million tons of NH3 annually. Iron catalysts are utilized to accelerate the reaction, but high temperatures and pressures of atmospheric nitrogen gas (N2) and hydrogen gas (H2) are required. A great deal of research has aimed at increased performance over the last century, but the rate of progress has been slow. This Account focuses on determining the atomic-level reaction mechanism for HB synthesis of NH3 on the Fe catalysts used in industry and how to use this knowledge to suggest greatly improved catalysts via a novel paradigm of catalyst rational design.We determined the full reaction mechanism on the two most active surfaces for the HB process, Fe(111) and Fe(211)R. We used density functional theory (DFT) to predict the free-energy barriers for all 12 important reactions and the 34 most important 2 × 2 surface configurations. Then we incorporated the mechanism into kinetic Monte Carlo (kMC) simulations run for several hours of real time to predict turnover frequencies (TOFs). The predicted TOFs are within experimental error, indicating that the predicted barriers are within 0.04 eV of experiment.With this level of accuracy, we are poised to use DFT to improve the catalyst. Rather than forming bulk alloys with uniform concentration, we aimed at finding additives that strongly prefer near-surface sites so that minor amounts of the additive might lead to dramatic improvements. However, even for a single additive, the combinations of surface species and reactions multiplies significantly, with ∼48 reaction steps to examine and nearly 100 surface configurations per 2 × 2 site. To make it practical to examine tens of dopant candidates, we developed the hierarchical high-throughput catalysis screening (HHTCS) approach, which we applied to both the Fe(111) and Fe(211) surfaces. For HHTCS, we identified the most important 4 reaction steps out of 12 for the two surfaces to examine >50 dopant cases, where we required performance at each step no worse than for pure Fe. With HHTCS, the computational cost is about 1% of that for doing the full reaction mechanism, allowing us to do ≈50 cases in about 1/2 the time it took to do pure Fe(111). The new leads identified with HHTCS are then validated with full mechanistic studies.For Fe(111), we predict three high-performance dopants that strongly prefer the second layer: Co with a rate 8 times higher, Ni with a rate 16 times higher, and Si with a rate 43 times higher, at 400 °C and 20 atm. We also found four dopants that strongly prefer the top layer and improve performance: Pt or Rh 3 times faster and Pd or Cu 2 times faster. For Fe(211), the best dopant was found to be second-layer Co with a rate 3 times faster than that for the undoped surface.The DFT/kMC data were used to predict reshaping of the catalyst particles under reaction conditions and how to tune dopant content so as to maximize catalytic area and thus activity. Finally, we show how to validate our mechanistic modeling via a comparison between theoretical and experimental operando spectroscopic signatures.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acs.accounts.1c00789.Schematic depiction of the bcc surface structures here investigated also showing 4-fold binding sites (PDF)This article has not yet been cited by other publications.

Beyond the Thermal Equilibrium Limit of Ammonia Synthesis with Dual Temperature Zone Catalyst Powered by Solar Light

Ammonia Synthesis Via Nitrogen-Coupled Methane Conversion at Ambient Temperature and Plasma Conditions

Regulating the Scaling Relations in Ammonia Synthesis through a Light-driven Bendable Seesaw Effect on Tailored Iron Catalyst

Innovative progress of thermal ammonia synthesis under mild conditions

Mechanochemistry for ammonia synthesis under mild conditions

Au Sub-Nanoclusters on TiO 2 toward Highly Efficient and Selective Electrocatalyst for N 2 Conversion to NH 3 at Ambient Conditions.

Efficient ammonia synthesis from the air using tandem non-thermal plasma and electrocatalysis at ambient conditions

Theoretical Approach Toward a Mild Condition Haber-Bosch Process on the Zeolite Catalyst with Confined Dual Active Sites

Non-thermal Atmospheric Plasma Synthesis of Ammonia in a DBD Reactor Packed with Various Catalysts

A novel solar system for photothermal-assisted electrocatalytic nitrate reduction reaction to ammonia

Electrochemical Synthesis of Ammonia by Zirconia-Based Catalysts at Ambient Conditions

Highly efficient ammonia synthesis at low temperature over a Ru–Co catalyst with dual atomically dispersed active centers

Understanding and Modifying the Scaling Relations for Ammonia Synthesis on Dilute Metal Alloys: From Single-Atom Alloys to Dimer Alloys

Atmospheric Pressure Ammonia Synthesis on AuRu Catalysts Enabled by Plasmon-Controlled Hydrogenation and Nitrogen-species Desorption

Reaction Mechanisms, Kinetics, and Improved Catalysts for Ammonia Synthesis from Hierarchical High Throughput Catalyst Design

Energy-Confined Solar Thermal Ammonia Synthesis with K/Ru/TiO 2-x H x

Electromagnetic field-assisted low-temperature ammonia synthesis

Dielectric barrier discharge plasma-assisted catalytic ammonia synthesis: synergistic effect of Ni-MOF-74 catalyst and nanosecond pulsed plasma

Hydrogen Spillover to Oxygen Vacancy of TiO2-xHy/Fe: Breaking the Scaling Relationship of Ammonia Synthesis.

Atomic strategy to boost the solar heating ammonia decomposition of cobalt-based catalyst

Low-temperature synthesis of NH3 by an alternate gas-switching NOx storage reduction using a BaO/Pt@mTiO2 type nanocomposite catalyst