Abstract:The Haber–Bosch (HB) process is the primary chemical synthesis technique for industrial production of ammonia (NH3) for manufacturing nitrate-based fertilizer and as a potential hydrogen carrier. The HB process alone is responsible for over 2% of all global energy usage to produce more than 160 million tons of NH3 annually. Iron catalysts are utilized to accelerate the reaction, but high temperatures and pressures of atmospheric nitrogen gas (N2) and hydrogen gas (H2) are required. A great deal of research has aimed at increased performance over the last century, but the rate of progress has been slow. This Account focuses on determining the atomic-level reaction mechanism for HB synthesis of NH3 on the Fe catalysts used in industry and how to use this knowledge to suggest greatly improved catalysts via a novel paradigm of catalyst rational design.We determined the full reaction mechanism on the two most active surfaces for the HB process, Fe(111) and Fe(211)R. We used density functional theory (DFT) to predict the free-energy barriers for all 12 important reactions and the 34 most important 2 × 2 surface configurations. Then we incorporated the mechanism into kinetic Monte Carlo (kMC) simulations run for several hours of real time to predict turnover frequencies (TOFs). The predicted TOFs are within experimental error, indicating that the predicted barriers are within 0.04 eV of experiment.With this level of accuracy, we are poised to use DFT to improve the catalyst. Rather than forming bulk alloys with uniform concentration, we aimed at finding additives that strongly prefer near-surface sites so that minor amounts of the additive might lead to dramatic improvements. However, even for a single additive, the combinations of surface species and reactions multiplies significantly, with ∼48 reaction steps to examine and nearly 100 surface configurations per 2 × 2 site. To make it practical to examine tens of dopant candidates, we developed the hierarchical high-throughput catalysis screening (HHTCS) approach, which we applied to both the Fe(111) and Fe(211) surfaces. For HHTCS, we identified the most important 4 reaction steps out of 12 for the two surfaces to examine >50 dopant cases, where we required performance at each step no worse than for pure Fe. With HHTCS, the computational cost is about 1% of that for doing the full reaction mechanism, allowing us to do ≈50 cases in about 1/2 the time it took to do pure Fe(111). The new leads identified with HHTCS are then validated with full mechanistic studies.For Fe(111), we predict three high-performance dopants that strongly prefer the second layer: Co with a rate 8 times higher, Ni with a rate 16 times higher, and Si with a rate 43 times higher, at 400 °C and 20 atm. We also found four dopants that strongly prefer the top layer and improve performance: Pt or Rh 3 times faster and Pd or Cu 2 times faster. For Fe(211), the best dopant was found to be second-layer Co with a rate 3 times faster than that for the undoped surface.The DFT/kMC data were used to predict reshaping of the catalyst particles under reaction conditions and how to tune dopant content so as to maximize catalytic area and thus activity. Finally, we show how to validate our mechanistic modeling via a comparison between theoretical and experimental operando spectroscopic signatures.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acs.accounts.1c00789.Schematic depiction of the bcc surface structures here investigated also showing 4-fold binding sites (PDF)This article has not yet been cited by other publications.

Regulating the Scaling Relations in Ammonia Synthesis through a Light-driven Bendable Seesaw Effect on Tailored Iron Catalyst

Understanding and Modifying the Scaling Relations for Ammonia Synthesis on Dilute Metal Alloys: From Single-Atom Alloys to Dimer Alloys

Beyond the Thermal Equilibrium Limit of Ammonia Synthesis with Dual Temperature Zone Catalyst Powered by Solar Light

Modulating Electronic Metal‐Support Interactions to Boost Visible‐Light‐Driven Hydrolysis of Ammonia Borane: Nickel‐Platinum Nanoparticles Supported on Phosphorus‐Doped Titania

Innovative progress of thermal ammonia synthesis under mild conditions

Reaction Mechanisms, Kinetics, and Improved Catalysts for Ammonia Synthesis from Hierarchical High Throughput Catalyst Design

Activating nano-bulk interplays for sustainable ammonia electrosynthesis

Regulated Dual Defects of Bridging Organic and Terminal Inorganic Ligands in Iron‐based Metal‐Organic Framework Nodes for Efficient Photocatalytic Ammonia Synthesis

Highly Efficient Ni-Doped Iron Catalyst for Ammonia Synthesis from Quantum-Mechanics-Based Hierarchical High-Throughput Catalyst Screening

Theoretical Approach Toward a Mild Condition Haber-Bosch Process on the Zeolite Catalyst with Confined Dual Active Sites

Si-Doped Fe Catalyst for Ammonia Synthesis at Dramatically Decreased Pressures and Temperatures

A Graphene Oxide‐supported PdCu Catalyst for Enhanced Electrochemical Synthesis of Ammonia

Interfacial Engineering of Cobalt Sulfide/graphene Hybrids for Highly Efficient Ammonia Electrosynthesis

Boosting electrochemical ammonia synthesis via dynamic nitrogen carriers coupled with electron-rich Lewis acidic sites on TiO2-x nanofiber

Highly efficient ammonia synthesis at low temperature over a Ru–Co catalyst with dual atomically dispersed active centers

Mechanochemistry for ammonia synthesis under mild conditions

Achieving a Thermodynamic Self‐Regulation Dynamic Adsorption Mechanism for Ammonia Synthesis through Selective Orbital Coupling

Hydrogen Spillover to Oxygen Vacancy of TiO2-xHy/Fe: Breaking the Scaling Relationship of Ammonia Synthesis.

Controlling the Shapes of Nanoparticles by Dopant-Induced Enhancement of Chemisorption and Catalytic Activity: Application to Fe-Based Ammonia Synthesis

Modulating Single‐Atom Palladium Sites with Copper for Enhanced Ambient Ammonia Electrosynthesis

Fullerene on non-iron cluster-matrix co-catalysts promotes collaborative H2 and N2 activation for ammonia synthesis