Abstract:{1011}-{1012} double twin is the most common twin type being observed in the rolled AZ31 magnesium alloy, especially at low or moderate rolling temperature. Four types of rolled AZ31 magnesium alloy sheets were produced by rolling strong basal textured AZ31 plates at 150°C and 300°C respectively through different rolling paths by two passes till total reduction 17%. The rolling paths are normal and cross rolling respectively: the rolling directions of the two passes for normal rolling are mentally paralleled while perpendicular to each other for the cross rolling. Sheets are characterized in terms of microstructure and texture using optical microscope and scanning-electron microscope equipped with EBSD detector, and their mechanical performances are measured by uniaxial tensile tests at room temperature and a strain rate of 0.001 s -1. Tensile samples are cut parallel or perpendicular to the final rolling direction to obtain the mechanical anisotropies. The effects of the {1011}-{1012} double twins occurred during rolling on the microstructure, texture and mechanical properties of the rolled sheets are discussed and related to each other. The results show that the fraction of {1011}-{1012} double twins varies widely in different rolled sheets, which are determined by the rolling temperature. The twins in different rolled sheets are arranged in different ways. In the normal rolled sheets, the traces of twins are approximately perpendicular to the final rolling direction, while in the cross rolled sheets there are both traces of twins parallel and to the final directions. This phenomenon is related to the variant selection of twinning during rolling deformation. And the variant selection law is related to the rolling direction. For the same reason, the textures of twins in the rolled sheets produced through different paths are different. The textures of twins will add onto the bulks, and increases the textural difference between the bulks. The differences between mechanical properties of the rolled sheets are also related to the different textures and microstructures of the sheets caused by twins. © Right.

Evaluation of Twinning Behavior in Rolling of Mg Alloys with Three Kinds of Textures by a Generalized Schmid Factor

Twinning character and texture origination in the randomly-oriented AZ31B magnesium alloy during cold-rolling

Twinning Behavior of a Strongly Basal Textured AZ31 Mg Alloy During Warm Rolling

Observation and Schmid Factor Analysis of Multiple Twins in a Warm-Rolled Mg–3Al–1Zn Alloy

Evolution of Twins and Texture and Its Effects on Mechanical Properties of AZ31 Magnesium Alloy Sheets under Different Rolling Process Parameters

Twinning, Grain Orientation, and Texture Variations in Mg Alloy Processed by Pre-Rolling

Effect of Al addition and rolling reduction on microstructure and texture evolution of Mg–3Sn alloy during high-speed rolling

Twinning-Assisted Static Recrystallization and Texture Evolution in A Mg-Gd-Y-Zr Alloy

Orientation analyses for twinning behavior in small-strain hot-rolling process of twin-roll cast AZ31B sheet

The effect of {1011}-{1012} double twinning on the microstructure, texture and mechanical properties of AZ31 magnesium alloy sheet during rolling deformation

The Role of Al Content on Deformation Behavior and Related Texture Evolution During Hot Rolling of Mg-Al-Zn Alloys

Evaluation of Textural Effect on the Rollability of AZ31 Alloys by Wedge‐Shaped Sample Design

Tailoring the Rolling Texture of AZ31 Mg Alloy with Calcium and Tin Addition

The effect of {10¯11}–{10¯12} double twinning on the microstructure, texture and mechanical properties of az31 magnesium alloy sheet during rolling deformation

Enhanced rollability of Mg alloys by directly activated { 10 1 ̄ 2 } twinning during asymmetric rolling: Experiments and finite element analysis

Observation and Analysis of the Coexistence of Two “opposite” Twin Modes in a Mg-Al-Zn Alloy

A quantitative study on mechanical behavior of Mg alloys with bimodal texture components

Effect of rolling geometry on the mechanical properties, microstructure and recrystallization texture of Al-Mg-Si alloys

Microstructure, Texture and Mechanical Properties Evolution of Pre-Twinning Mg Alloys Sheets During Large Strain Hot Rolling

Influence Research of Al and Zn Addition for Twin Roll Casting Magnesium During Multi-Pass Hot Rolling

Texture evolution and twinnability prediction of the most compliant orientation in GH3536 superalloy during cold rolling