Abstract:In this study, the hot uniaxial compression of the heat-treated Mg-12Y–1Al alloy containing long-period stacking ordered (LPSO) phase was conducted by a Gleeble-3500 simulator. Compressive mechanical properties at elevated temperatures and the effects of deformation temperature (300–450 °C) and strain rate (0.001–1 s −1 ) on the hot deformation behavior of the alloy were systematically investigated. Combining with an optical microscope (OM), electron backscatter diffraction (EBSD), and in-grain misorientation axes (IGMA) analysis, the microstructure and texture evolution, dislocation slip, and dynamic recrystallization (DRX) mechanism of the alloy was studied in detail. The results showed that the flow stress decreased with the increase in temperature and the decrease in strain rate. At a strain rate of 1 s −1 , the compressive strength at 300 °C and 350 °C was basically the same. After deformation, the morphology of Al 2 Y had almost no change, while the LPSO underwent apparent kinking deformation. The increase in temperature was conducive to DRX. The DRX mechanism of the alloy mainly included discontinuous dynamic recrystallization (DDRX) and continuous dynamic recrystallization (CDRX), and DDRX was dominant. The dense lamellar LPSO at the grain boundary was detrimental to the occurrence of DDRX. In addition, the deformed microstructure presented a typical [0001]//CD (compression direction) texture. With the increase in temperature, the texture intensity decreased progressively due to the activation of multiple slip systems and the increased DRX fraction. At a strain rate of 0.01 s −1 , when the temperature increased to 450 °C, the number of deformed grains dominated by pyramidal II slip increased substantially.

Flow Behavior and Formability of Hot-Rolled Mg-8Gd-3Y Alloy under Double-Pass Isothermal Compression

Hot Deformation and Processing Map of As-Homogenized Mg–9Gd–3Y–2Zn–0.5Zr Alloy

Effects of Holding Time and Zener-Hollomon Parameters on Deformation Behavior of Cast Mg-8Gd-3Y Alloy During Double-Pass Hot Compression

Mechanical Behavior and Microstructure Evolution of Mg-Gd-Y-Zn-Zr Alloy during Multipass Hot Compression Deformation

Numerical and Experimental Investigation on Hot Backward Extrusion Process of Mg-Gd-Y-Zn-Zr Magnesium Alloy

3D Processing Maps of Cast Mg-8Gd-3Y Alloy at High Strain Rates and Their Application in Plane Strain Forging

The abnormal flow behavior of Mg-9Gd-4Y-2Zn-0.5Zr alloy during hot tensile deformation at high temperature and low strain rate

Hot Compression Deformation Behavior and Processing Maps of Mg-Gd-Y-Zr Alloy

Hot Compression Deformation Behavior of Mg-9Gd-2.9Y-1.9Zn-0.4Zr-0.2Ca (wt%) Alloy

Hot deformation and processing maps of as-extruded Mg–9.8Gd–2.7Y–0.4Zr Mg alloy

Hot Deformation Behavior and Finite Element Simulation of Mg–8.3Gd–4.4Y–1.5Zn–0.8Mn Alloy

Optimization of Hot Backward Extrusion Process Parameters for Thin-Walled Tubes of Mg-9Gd-3Y Alloy Based on 3D Processing Maps

Hot Deformation Behaviour and Constitutive Equation of Mg-9Gd-4Y-2Zn-0.5Zr Alloy

Hot compression behavior, simulation verification and dynamic recrystallization mechanism of Mg-Gd-Y-Zr alloy

Investigation of hot deformation behavior of Mg-14Gd-0.5Zr (wt%) through constitutive analysis and processing maps

Flow softening and dynamic recrystallization behavior of a Mg-Gd-Y-Nd-Zr alloy under elevated temperature compressions

Influence of Multi-Pass Hot Extrusion on Microstructure and Mechanical Properties of the Mg–4Zn–1.2Y–0.8Nd Alloy

Unveiling the Microstructural Features during Compression of a High-Modulus Mg-15Gd-8Y-6Al-0.3Mn Alloy Reinforced by a Large Volume of Al2RE Phases

High Temperature Compressive Deformation Behavior of an Extruded Mg–8Gd–3Y–0.5Zr (wt.%) Alloy

Hot Deformation Behavior and Microstructural Evolution of Twin-Roll-Casting Mg Alloy during High-Temperature Compression

Revealing the deformation behavior and microstructure evolution in Mg-12Y–1Al alloy during hot compression