Abstract:Mg–6.0 Zn–2.0 Yb–0.5 Zr (wt.%) alloy exhibits excellent strength and ductility synergy after thermomechanical and heat treatment. Unfortunately, the hot workability and microstructure evolution under specific deformation regimes remain uncertain to date. In this work, the constitutive model and hot processing maps were established based on a series of isothermal compression tests. A detailed examination of deformation microstructures at different processing regimes revealed that the hot workability and correlated microstructure development were deformation condition dependent. When compressed at lower strain rates and higher deformation temperatures, the softening was promoted by dynamic recrystallization (DRX) and the prevalence of discontinuous dynamic recrystallization (DDRX) generally resulted in a complete DRX process with coarse grains and much-intensified texture. On the contrary, work hardening was improved with increasing dislocation density, and the continuous DRX (CDRX) may control the partial DRX progress, often presenting a much-refined microstructure with a more dispersed texture. Interestingly, a low strain rate of 0.001 s −1 and a moderate deformation temperature of 300 °C effectively balanced the nucleation rate and grain growth to finally achieve a much refined and relatively homogeneous grain structure. Further investigation concerning the activation energy suggested that the workability improved with increasing strain rate and temperature. Enhanced hot workability at most deformation regimes was achieved due to a lower average activation energy Q value in comparison with that of 1.0 wt.% Yb alloyed ZK60 counterpart, which was likely due to a higher activity of non-basal slips achieved in this alloy.

Hot Deformation Behavior of Rare Earth Magnesium Alloy Without Pre-Homogenization Treatment

Hot Deformation and Processing Map of As-Homogenized Mg–9Gd–3Y–2Zn–0.5Zr Alloy

Hot Deformation Behaviour and Constitutive Equation of Mg-9Gd-4Y-2Zn-0.5Zr Alloy

Hot Deformation Behavior and Processing Map of Coarse-Grained Mg–Gd–Y–Nd–Zr Alloy

Hot Deformation Behavior and Finite Element Simulation of Mg–8.3Gd–4.4Y–1.5Zn–0.8Mn Alloy

Constitutive Equation and Hot Processing Map of Mg-16Al Magnesium Alloy Bars

The abnormal flow behavior of Mg-9Gd-4Y-2Zn-0.5Zr alloy during hot tensile deformation at high temperature and low strain rate

Deformation Behavior and Dynamic Recrystallization of Mg-Y-Nd-Gd-Zr Alloy

Characterization of Hot Deformation Behavior and Processing Maps of Homogenized Al-Mg-Si-Sc-Zr Alloys

Numerical and Experimental Investigation on Hot Backward Extrusion Process of Mg-Gd-Y-Zn-Zr Magnesium Alloy

Hot deformation behavior and microstructure evolution of as-cast AZ91D magnesium alloy without pre-homogenization treatment

Study on Hot Compression Deformation and Processing Map of Mg-6Al-2Si-1.5Er Mg Alloy

Hot compression behavior and microstructure evolution of Mg-Gd-Y-Zn-Zr alloy

Hot deformation behavior of AZ40 magnesium alloy at elevated temperatures

Establishment and Application of Flow Stress Models of Mg-Y-Mm-Zr Alloy

Hot deformation behavior of novel high-strength Mg-0.6Mn-0.5Al-0.5Zn-0.4Ca alloy

Thermal Deformation Behavior and Processing Maps of As-Homogenized Mg-5.8 Zn-0.5 Zr-1.0 Yb Alloy

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

The high-temperature deformation and microstructural evolution mechanism of Mg-Gd-Y-Zn-Zr alloy formed by CMT arc additive forming

Hot workability and microstructure of Mg–6.0 Zn–2.0 Yb–0.5 Zr magnesium alloy

Study on Hot Deformation Behavior of Mg-9Y-1MM-1Zn-0.6Zr Alloy