Abstract:Abstract Additive Manufacturing (AM) of ceramics is a constantly emerging field of interest both in research and in industry. Binder jetting-based AM of ceramics in particular offers the opportunity to produce large ceramic parts with a high wall thickness at a high throughput. One limitation is that it requires flowable powders, which are generally coarse and thus exhibit only limited sintering activity. The resulting low sintered densities impede the commercial binder jetting-based production of dense oxide ceramics. We present an approach to efficiently increase the green density of binder jetted alumina parts by optimized slurry infiltration, which also leads to a significant increase in the sintered density. In a first step, alumina parts were fabricated via binder jetting, using a 20-μm-sized alumina powder, yielding relative green densities of about 47–49%. Initial sintering studies with powder compacts showed that sintering even above 1900 °C is not sufficient to achieve acceptable densification. Therefore, green samples were infiltrated with a highly filled ceramic slurry to fill the remaining pores (about 2–5 μm in size) with smaller particles and thus increase the packing density. Particle volume content (40–50 vol%), particle size (100–180 nm) and the infiltration procedure were adapted for tests on cuboid samples to achieve a high penetration of the green bodies and a high degree of pore filling. In this way, the relative green density could be increased starting from about 47% after binder jetting, to 73.4% after infiltration and drying. After sintering at 1675 °C densities above 90% could be achieved, yielding three-point bending strengths up to 145 MPa. As a conclusion, this approach can be regarded as a promising route for overcoming the drawbacks of the binder jetting process on the way to denser, mechanically more stable sintered alumina parts.

Additive Manufacturing of Thin Alumina Ceramic Cores Using Binder-Jetting

Significantly Improved Sintering Shrinkage of Heavy Calcium Carbonate Ceramic Cores by Binder Jetting Using Al Powder Additive

Preparation of Low-Cost High Strength Soluble Ceramic Cores Using Heavy Calcium Carbonate by Binder Jetting and Vacuum Impregnation

Properties Comparison of Pure Al2O3 and Doped Al2O3 Ceramic Cores Fabricated by Binder Jetting Additive Manufacturing

Effect of sodium silicate solution combined yttrium oxide stabilized zirconia nanopowders on the properties of alumina ceramics fabricated by binder jetting additive manufacturing

Characterization of ceramic components fabricated using binder jetting additive manufacturing technology

Binder Jetting Additive Manufacturing of Ceramics: A Literature Review

Effect of Sintering Aid Combined Vacuum Infiltration on the Properties of Al2O3-based Ceramics Via Binder Jetting

Effect of sintering aid combined vacuum infiltration on the properties of Al 2 O 3 -based ceramics via binder jetting

Water-Soluble Sand Core Made by Binder Jetting Printing with the Binder of Potassium Carbonate Solution

3D Printing of CaO-based Ceramic Core Using Nanozirconia Suspension As a Binder

Binder Jetting Yttria Stabilised Zirconia Ceramic with Inorganic Colloid As a Binder

Fabricating an Effective Calcium Zirconate Layer over the Calcia Grains Via Binder-Jet 3D-Printing for Improving the Properties of Calcia Ceramic Cores

Improved green and sintered density of alumina parts fabricated by binder jetting and subsequent slurry infiltration

Hydrothermal-Assisted Transient Binder Jetting of Ceramics for Achieving High Green Density

Effect Of Zirconia Content And Particle Size On The Properties Of 3d-Printed Alumina-Based Ceramic Cores

Direct ink writing additive manufacturing of porous alumina-based ceramic cores modified with nanosized MgO

A novel composite binder design for direct ink writing alumina-based ceramics with enhanced strength at low sintering temperature

Optimization of the injection molding process for development of high performance calcium oxide -based ceramic cores

A thermal-initiated monomer binder enhancing green strength with low binder saturation for binder jetting additive manufacturing of cemented carbide

Layered Extrusion Forming—a Simple and Green Method for Additive Manufacturing Ceramic Core