Abstract:Carbon nanotubes (CNTs) have outstanding characteristics including high mechanical properties, namely tensile strength and elastic modulus,and still remarkable flexibility, excellent thermal and electric conductivities, low percolation thresholds (loading weight at which a sharp drop in resistivity occurs) and high aspect ratios (length to diameter ratio, L/D) while the latter provides the nanotubes with additional advantage over spherical fillers to obtain high property composites. Therefore I CNTs have the potential to act as a reinforcing filler of polymer matrices. The tetraglycidyl-4,4'-diaminodiphenylmethane (TGDDM) cured with 4,4'-diaminodiphenylsulphone WDS) and filled with graphite or carbon fibers are commonly used as a polymeric matrix in high performance composites employed in the aircraft and spacecraft industries. In present paper, multi-walled carbon nanotubes (MWNTs) as a nano-filler were incorporated in the TGDDM/DDS epoxy. The thermal properties of the composites were studied by differential scanning calorimetry (DSC), dynamic thermal analysis (DMTA) and thermal gravitimetric analysis TGA). In addition, the dispersion of MWNTs in the epoxy was also investigated by scanning electron microscopy SEM). In DSC studies, Kissinger and Flynn-Wall-Ozawa (FWO) methods were used to study the nonisothermal cure kinetics of the MWNTs filled TGDDM/DDS composites at different heating rates. The activation energy (E.) of cure reactions of the MWNTs filled epoxy composites was obtained by Kissinger and FWO methods. For all composites, the E. obtained by Kissinger method was slightly less than that of FWO method. With the addition of MWNTs, the E. of the epoxy composites decreased first and then increased with the increase of the MWNTs contents. These results showed that the incorporation of carbon nanotubes accelerated the cure reaction of the TGDDM/DDS epoxy at lower MWNTs content due to the interaction between the hydroxyl groups on the surface of nanotubes and the epoxy. However, due to the high surface energy of carbon nanotubes, the viscosity of MWNTs/epoxy composites increased at higher MWNTs content. Hence, the mobility of hydroxyl groups was hindered, and the reaction energy of composites increased with increasing MWNTs contents. The influence of carbon nanotubes on the thermal stability of the epoxy was studied by TGA. It is shown that MWNTs had little influence on the thermal stability of the cured epoxy. The storage modulus and glass transition temperature of MWNTs filled TGDDM/DDS were investigated by DMTA. It is seen that the storage modulus of TGDDM/DDS system was enhanced with the increasing of MWNTs content, that is, the modulus increased 6.3% and 7.8% at 1 wt % and 5 % MWNTs content, respectively. The glass transition temperature of the epoxy slightly decreased. Furthermore, the DMTA results of MWNTs/TGDDM/DDS composites were compared with that of carbon narrofibers (CNFs)/TGDDM/DDS composites. It was shown that the interactions between CNFs and epoxy were better those between that MWNTs and epoxy. The dispersion of carbon nanotubes in the epoxy was studied by SEM. The SEM results suggest that of MWNTs had poor dispersion in the cured epoxy. However, the radii of carbon nanotubes in the epoxy were greater than those of pure nanotubes. These results show the existence of interaction between carbon nanotubes and epoxy.

Mechanical Properties of Carbon Nanotube Fibers Reinforced Epoxy Resin Composite Films Prepared by Wet Winding

Length-dependent Electrical and Thermal Properties of Carbon Nanotube-Loaded Epoxy Nanocomposites

Reducing Dispersity of Mechanical Properties of Carbon Fiber/epoxy Composites by Introducing Multi-Walled Carbon Nanotubes

Single Carbon Fiber/Acid-Treated CNT-Epoxy Composites by Electro- Micromechanical Technique and Wettability Test for Dispersion and Self-Sensing

Carbon-nanotube-templated Carbon Nanofibers with Improved Mechanical Performance

Preparation of carbon nanotube/epoxy composite films with high tensile strength and electrical conductivity by impregnation under pressure

High-strength and toughness carbon nanotube fiber/resin composites by controllable wet-stretching and stepped pressing

Tensile Mechanical Behaviors of High Loading of Carbon Nanotube/Epoxy Composites via Experimental and Finite Element Analysis

Carbon Nanotube/Epoxy Composites Fabricated by Resin Transfer Molding

Influence of Carbon Nanotube Coatings on Carbon Fiber by Ultrasonically Assisted Electrophoretic Deposition on Its Composite Interfacial Property.

PREPARATION AND MECHANICAL PROPERTIES OF CARBON NANOTUBES/RESIN EPOXY COMPOSITE

High performance, freestanding and superthin carbon nanotube/epoxy nanocomposite films.

A Modified Spray-Winding Approach to Enhance the Tensile Performance of Array-Based Carbon Nanotube Composite Films

Preparation and functional study of epoxy composites reinforced with ultra-low content single-walled carbon nanotubes

Enhanced thermomechanical properties of epoxy-multiwalled CNT nano-composites

Insight into the mechanical properties and thermal expansion behavior of epoxy nanocomposites reinforced with multi‐walled carbon nanotube solvent‐free nanofluids

The mechanical and electrical properties of direct-spun carbon nanotube mat-epoxy composites

Study on Mechanical Properties of Carbon Nanotube Reinforced Carbon Fiber/ Epoxy Resin Composites

Mechanical properties of a carbon fiber reinforced epoxy resin composite improved by integrating multi-walled carbon nanotubes and graphene nanoplatelets

Thermoanalytical Studies of High Performance Epoxy/Carbon Nanotube Composites

Study on Mechanical Properties of Carbon Nanotube Reinforced Composites