Abstract:Empirical wear transition maps have been constructed to delineate the load velocity conditions under which wear transitions occurred in an A356 AI alloy and an A356 Al20%SiC composite. Experiments were performed in dry sliding conditions, using a block-on-ring (SAE 52100) configuration, within a load range of 0.2–400 N and a sliding velocity range of 0.2–5.0 m s−1. Both materials displayed transitions from mild to severe wear at specific load and sliding velocity combinations. The mild wear regime for the composite was expanded to a higher range of sliding speeds and loads by comparison with unreinforced A356 Al. Within the mild regime, two sub-regimes existed for both materials, namely where mixing/oxidation occurred at low sliding speeds to produce a thermally insulating surface layer, and another at higher speeds where this layer was removed. In the composite an additional wear transition, i.e. from mild to ultra-mild regime, occurred at low loads and velocities where the wear rates of the composite were at least two orders of magnitude lower than unreinforced A356 Al, due to the load supporting effect of the particles at the contact surfaces. In both materials, the transition from mild to severe wear occurred at conditions where the surface (bulk) temperature exceeded a critical value of approximately 125 °C in the A356 Al and 338 °C for the composite. The temperature data were summarised in the form of surface temperature maps on log load versus log velocity axes.Wear mechanisms in each regime were determined using scanning electron microscopy, and energy dispersive spectroscopy techniques that were used to analyse morphologies, microstructures and chemical compositions of worm surfaces and wear debris. The dominant mechanisms in each regime were identified and correlated with wear rate and temperature map data to summarise the effects of reinforcement on wear rates and transitions.

Wear Regime and Wear Mechanism Map for Spark-Plasma-Sintered Cu-15Ni-8Sn-0.2Nb Alloy under Oil Lubrication

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

Tribological Behavior of Plasma-Sprayed Metal Based Solid Self-Lubricating Coatings under Heavy Load

Wear of Cu–15Ni–8Sn Spinodal Alloy

Dry sliding wear of Cu–15Ni–8Sn alloy

Friction and Wear Properties of Wide-Velocity Range High-Energy Plasma Sprayed CuSn-NiCr Solid Self-Lubricating Coatings under Heavy Load

Wear mechanism, subsurface structure and nanomechanical properties of additive manufactured Inconel nickel (IN718) alloy

Tribological behavior of SAPS sprayed Al2O3-TiO2 and NiCr-Cr3C2 coatings under severe load conditions

THE WEAR BEHAVIOR OF BRUSH-PLATED Ni-W-Co/SiC COMPOSITE LAYER WITH OIL LUBRICATION

Dry sliding wear behavior of additively manufactured CoCrWNixAly alloys

Wear mechanism maps for metal matrix composites

Unlubricated Wear of Si/SiC and Its Composite with Nickel Si/SiC-Ni

Numerical simulation on high-speed and heavy-load wear behavior of CoCrNi and CoCrFeMnNi alloys

Correlating numerical modelling with experimental studies to quantify the wear resistance of high-carbon chromium bearing steel in mixed lubrication

Microstructural Optimization and Anti-Wear Performance of Supersonic Atmospheric Plasma Sprayed Nickel Based Self-Lubricating Coatings under Heavy Load

The relevance of wear-mechanism maps to mild-oxidational wear

Influence of Cu Content Variation on the Tribological Properties of Ni60CuMo with Sandwich-Structured Composite Coatings by Laser Cladding

Microstructure and Wear Resistance of Laser-Clad Ni–Cu–Mo–W–Si Coatings on a Cu–Cr–Zr Alloy

Wear-resistant CrCoNi nanocrystalline film via friction-driven surface segregation

Sliding Wear Performance of CuNiCoBe Material

Torsional Fretting and Torsional Sliding Wear Behaviors of CuNiAl Against 42crmo4 under Dry Condition