Abstract:Thermometry based on nitrogen-vacancy (NV) center in diamond realizes temperature sensing by measuring the zero field splitting parameter (D) between the sublevels of its ground state. Since diamond has high stability, the resistance to interference, and can be processed into different sizes, thermometry is regarded as a feasible solution to high-precision temperature measurement on the micro-nano scale, which has the potential to be developed into practical application. In the measurement of D, the laser is applied to excite spin polarization and a microwave is then used to manipulate the electron spin. The optically detected magnetic resonance (ODMR) spectrum is obtained by detecting fluorescence released in the transition of the electrons, and the spectral lines are fitted to determine the values of D. Fluctuation of laser power is one of the important sources of experimental noise. To realize a high probability of spin polarization applying laser with high power is necessary. However, the fluctuation at a relatively high laser power will influence the probability of spin polarization, decrease the stability of the fluorescence intensity detected, and increase the error of data. The traditional method, which outputs the photon count rate directly without any reference for normalization, will reflect the fluctuation of laser power in the spectrum. This paper proposes a method to reduce the laser-induced error, in which a reference value of photon count without effective manipulation of microwave can be measured at each count using a specifically-encoded pulse sequence, and normalized fluorescence intensity will be obtained in the spectrum after normalizing the photon count under the manipulation of microwave to the reference. In this way, the effect of the laser power fluctuation on the spectrum will be weakened. The comparative experiments were carried out at 300 K on the ODMR measurement system built in the laboratory. A count time of 0. 8 s and a preparation time of 0. 001 s were determined considering the optimization of the two time-related parameters. Under different laser powers, three groups of D values were measured by the direct fitting, mathematical, and pulse code normalization methods. The experimental results demonstrate that using pulse code to obtain reference for normalization can effectively suppress laser-induced error to 62. 5% of that without any reference, and improve the data accuracy from 179 kHz with no reference and 165 kHz with mathematical reference to 56. 9 kHz by comparison. The method can effectively suppress the laser-induced error, improve the resolution of the determination of D, and lay a foundation for the practical development of thermometry based on NV centers.

Improved Method of Excitation Signal in Transient Temperature Calibration System Based on Laser

Spatial-Temporal Distortions And Calibration Of Ultrashort Pulses In Complex Optical Systems

Modified Homodyne Laser Interferometer Based on Phase Modulation for Simultaneously Measuring Displacement and Angle.

Laser pointing error analysis and compensation method of low-power laser diode source applied to triangulation ranging system

Machine learning based laser homogenization method

Pursuing Reliability and Sensitivity of Pr3+ Fluorescence Temperature Sensing: Through the Lens of Excitation Strategy

Analysis and Suppression of Laser-Induced Error in Temperature Measurement Based on Nitrogen-Vacancy Centers in Diamond

High-Precision Temperature Control of Laser Crystals

Precise Gas Temperature Measurement Using a Single Dual-Wavelength Mode-Locked Fiber Laser

Study on the Influence of the Response Characteristics of A Temperature Sensor on the Measurement Accuracy of A Water-Absorption-Based High-Energy Laser Energy Meter

Transient emission wavelength estimation for DFB laser with temperature tuning

High-Resolution Temperature Sensor Based on Single-Frequency Ring Fiber Laser via Optical Heterodyne Spectroscopy Technology

Development of a small-size laser triangulation displacement sensor and temperature drift compensation method

Temperature control system for frequency stabilization of total internal cavity microchip laser

Dynamic Evolution of Microcavity Raman Laser Subjected to Frequency-Shifted Feedback and Its Application in Laser Spectrum Encoding Thermal Sensing

A New Method of Background Elimination and Baseline Correction for the First Harmonic

Optomechanically Mode-Locked Laser Sensor for High Accuracy Temperature Measurement

Analytical Solution And Experimental Verification For Pulsed Laser Heating Process With Convective Boundary Condition

Research On Measuring The Transient Temperature Of Selective Laser Sintering

High-frequency flashing of light source for synchronous measurement of temperature and deformation at elevated temperature

Improved sensitivity of temperature sensor based on three-photons pumped upconversion in highly transparent Er3+ doped lead lanthanum zirconate titanate ceramics